Walker T27i Скачать руководство пользователя страница 70

Страница: 70 / 100

Maintenance Instructions

T27i

Cleaning

CLEANING

CAUTION

If a pressure washer is used on the ex-

posed working parts, avoid water on the

electrical parts and the engine cooling sys-

tem.

Engine Air Cleaner System

There are two main components in the engine air

cleaner system: a turbine precleaner and a Don-

aldson Radialseal™ air cleaner. Each component

is checked, cleaned and maintained on a different

schedule based on the filtering action required.

Each component is serviced as follows:

Turbine Precleaner

The turbine precleaner is mounted on a remote air

intake tube connected to the Donaldson air clean-

er. A spinning fan driven by the intake airflow

separates dust from the air, giving the initial stage

of air clean ing. Dust particles are exhausted

through a single small vent in the side of the hous-

ing. Since no dust is trapped, the precleaner oper-

ates without clean ing. The only maintenance

required is to check the operation of the internal

fan

every 100 hours.

Verify operation:

1. Loosen the hose clamp and remove the tur-

bine precleaner.

2. Reach into the intake and check that the fan is

spinning freely. Reinstall the precleaner.

If the fan is not spinning, service or replace the

precleaner as required.

Engine Air Cleaner System Components

Dust Ejection

Valve

Donaldson Air

Cleaner Cover

Engine

Turbine

Precleaner

Tube

Safety

Filter

Primary Filter

Element

Air Filter

Restriction Gauge

Hose

Clamp

Air Intake

Hose

Cover

Latch

Mounting

Band

Hose

Clamps

Donaldson

Air Cleaner

Содержание T27i





































































































Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды

Walker T27i, Руководство оператора

Результаты поиска

Содержание T27i

Отзывы:

Бренды по названию

Популярные бренды