background image

3                                                                                                                          Walker Magnetics, Inc., NEO Permanent Lifting Magnet

SAFETY INSTRUCTIONS

GENERAL SAFETY RULES

 

Danger always exists when loads are transported by lifting devices, especially 

when the equipment is not being used properly or is poorly maintained. Because ac-
cidents and severe bodily injury or death can result, special safety precautions apply to 
the operation, inspection, and maintenance of the Walker Lift Magnets.

Following these simple rules can help to avoid lifting accidents:

Remember, proper lifting knowledge and techniques are the responsibility of the op-

erator. Be sure to read and understand the instructions and safety warnings contained in 
this manual before using your lifter.

If you do not understand everything in this manual contact Walker Magnetics for assistance 

before using the magnet.

Call 1-800-W-MAGNET

 

Always

 stay clear of the load.

 

Never

 lift loads over people or in close proxim-

ity to people.

 

Never

 attempt to operate this magnet until you 

read and understand the Operator’s Manual.

 

Never

 use this magnet to lift, support or trans-

port people.

 

Never

 leave any lifted load unattended.

 

Never

 lift more than one work piece at a time 

with this magnet.

 

Always

 make sure that the supporting struc-

ture and load attaching devices (i.e. crane, 
chains and hook) are rated to support the 
weight of the magnet and load.

 

Always

 make sure that the load’s weight and 

dimensions are within the Magnet’s Lifting 
Guidelines. These Guidelines are located in 
the Operator’s Manual.

 

Always

 let those near you know that a lift is to 

begin.

DANGER

Содержание NEO-125






























Отзывы: