Waldorf RN8110GE Скачать руководство пользователя страница 16

14 

Cleaning and Maintenance 

General 

Clean Target Top / Range regularly.  A clean appliance looks better, will last longer and will perform 

better.  Carbonised grease on cooking surfaces will hinder transfer of heat from cooking surface to 
food.  This will result in loss of cooking efficiency. 

 

DO NOT use water on Target Top while this item is still hot as warping and cracking may 

occur.  Allow Target Top / Range to cool down and then remove for cleaning

 

NOTE: 



DO NOT use abrasive detergents, strong solvents or caustic detergents as they could 
corrode or damage Target Top / Range. 



In order to prevent rust forming on Target Top, ensure that any detergent or cleaning 
material has been completely removed after each cleaning.  Appliance should be switched 
‘On’ briefly to ensure target top becomes dry. 

 

To keep your Target Top / Range clean and operating at peak efficiency, follow the procedures 

shown below:- 

 

After Each Use 

Clean Target Top / Range with a stiff nylon brush or a flexible spatula to remove any build up of 

carbon. 

 

Daily Cleaning 

1. 

Thoroughly clean splash back, interior and exterior surfaces of Target Top / Range with hot water, a 

mild detergent solution and a soft scrubbing brush. 

2. 

Clean control panel with a damp cloth lightly moistened with a solution of mild detergent and water.  

Wipe dry with a clean dry cloth. 

3. 

Brush Target Top (cast iron) with a soft bristled brush followed by wiping with a cloth to prevent  

accumulation of carbon. 

4. 

Remove drip tray and clean with a mild anti bacterial detergent and hot water solution using a soft 

bristled brush.  Dry drip tray thoroughly with a dry cloth. 

5. 

Dry Target Top / Range thoroughly with a dry cloth and polish with a soft dry cloth. 

 

Weekly Cleaning 

NOTE: 



If Target Top / Range usage is very high, we recommend that weekly cleaning procedure is 
carried out on a more frequent basis. 



Ensure that protective gloves are worn during cleaning process. 



DO NOT use harsh abrasive detergents, strong solvents or caustic detergents as they will 
damage Target Top / Range. 



DO NOT use water on Target Top / Range while it is still hot as cracking may occur.  Allow 
castings to cool and remove for cleaning. 

 
 

Always turn ‘Off’ electrical and gas supply before cleaning. 

This appliance is not water proof. 

Do not use water jet spray to clean interior or exterior of appliance. 

Caution 

Содержание RN8110GE




























Отзывы: