WAGO 8FDI 24V PROFIsafe 750-662/000-004 Скачать руководство пользователя

Страница: 121 / 128

WAGO I/O System

Glossary 121

750-662/000-004 8FDI 24V PROFIsafe

Manual

Version 1.0.0, valid from HW/SW Version 01/01

PL (Performance Level)

The performance level (PL) specifies the capacity of safety devices to execute a

safety function under foreseeable conditions.

PLC

A PLC (Programmable Logic Controller) is a device used to control a machine or

system and is programmed on a digital basis.

PROFIsafe

PROFIsafe Version 2.6 is used per PROFIsafe – Profile for Safety Technology on

PROFIBUS and PROFINET Profile part, related to IEC 61784-3-3 Technical

Specification Version 2.6 MU1.

PROFIsafe Address

Address that must be assigned to a safe device with PROFIsafe data

communication in order for data communication to be established between an

F host and F device.

Protected Installation

The goal of the protected installation of lines is, for example, operational reliability

and protection against stray voltages at different voltages in a cable or

equipment. Among other means, this is achieved by the necessary insulation

between two lines of different potentials.

PVi

Process Values Input

PVo

Process Values Output

Request

Event that causes the F I/O module to execute its safety function.

Response Time

See “Safety Response Time.”

Restart Inhibit

A restart inhibit is a means of preventing hazardous machine operation from

starting automatically after one or more of the following events:

- A safety function is triggered

- The operating mode of the machine changes

- The means for staring the machine changes

RIOforFA

Remote IO for Factory Automation Common Profile Specification for PROFINET

and PROFIBUS Version 1.10

Содержание 8FDI 24V PROFIsafe 750-662/000-004

































































































































Результаты поиска

Содержание 8FDI 24V PROFIsafe 750-662/000-004

Отзывы:

Похожие инструкции для 8FDI 24V PROFIsafe 750-662/000-004

Бренды по названию

Популярные бренды

WAGO 8FDI 24V PROFIsafe 750-662/000-004, Руководство пользователя

Результаты поиска

Содержание 8FDI 24V PROFIsafe 750-662/000-004

Отзывы:

Похожие инструкции для 8FDI 24V PROFIsafe 750-662/000-004

Бренды по названию

Популярные бренды