WAGO 8FDI 24V PROFIsafe 750-662/000-004 Скачать руководство пользователя

Страница: 16 / 128

16 Device Description

WAGO I/O System

750-662/000-004 8FDI 24V PROFIsafe

Manual

Version 1.0.0, valid from HW/SW Version 01/01

Device Description

The safe F I/O module is intended for functional safety

in the areas of industrial

automation technology, building technology and process technology, in order to

protect humans and machines according to Machinery Directive 2006/42/EC.

Connection to the safe PLC is established via the PROFINET IO fieldbus. The

F-I/O modules can be seamlessly integrated into the existing WAGO I/O

System 750.

Expensive, inflexible cabling is replaced by flexible, configurable safety functions,

thanks to secure PROFIsafe data transmission via the existing fieldbus system.

That makes it possible to optimize the F I/O module for different safety

applications.

The F I/O modules of the WAGO I/O System 750 can be used to implement

safety applications in accordance with the standards listed in Section

“Approvals” > “Applications”.

The following actuators and sensors can be operated at the inputs of the 750-

662/000-004 F I/O module (see Section “Commissioning” > “Connection

Examples”):

•

Potential-free emergency-off switches with contacts

•

Safety interlock switches

•

Operating mode selector switches

•

Safe sensors

•

Semiconductor outputs, compatible with type 1 inputs per IEC 61131-2

The 750-662/000-004 F I/O module has the following features:

•

Eight safety-oriented digital inputs I1 … I8

•

To clock outputs T1 and T2

•

Diagnostics via LED indicators and fieldbus protocol (per IEC 61784-1)

•

iPar server support for saving and restoring individual parameters

•

Channel granular passivation of inputs

•

Parameterizable channel and module properties

Functional safety evaluations were carried out by TÜV Rheinland.

Содержание 8FDI 24V PROFIsafe 750-662/000-004

































































































































Результаты поиска

Содержание 8FDI 24V PROFIsafe 750-662/000-004

Отзывы:

Похожие инструкции для 8FDI 24V PROFIsafe 750-662/000-004

Бренды по названию

Популярные бренды

WAGO 8FDI 24V PROFIsafe 750-662/000-004, Руководство пользователя

Результаты поиска

Содержание 8FDI 24V PROFIsafe 750-662/000-004

Отзывы:

Похожие инструкции для 8FDI 24V PROFIsafe 750-662/000-004

Бренды по названию

Популярные бренды