WAGO 761-214 Скачать руководство пользователя страница 95

Страница: 95 / 102

WAGO-TO-PASS® 761

Diagnostics

761-214 Telecontrol Module Compact, 8 AI, ESP, DSP

Manual

Version 2.0.0

Diagnostics

9.1

Test Inputs and Outputs

To test the inputs and outputs select the menu option

Controller > Test I/O

The following window is displayed:

Figure 38: Test inputs and outputs

The process values of the inputs are displayed in the upper area and the process
values of the outputs are displayed in the lower area.

By pressing the buttons

[Output 1]

…

[Output 4]

in the upper area switch digital

inputs on and off.

A value range of 0 mA … 20 mA and 4 mA … 20 mA is defined for the analog
outputs. No decimal places can be entered.
Enter the required numerical value and click the

[Set]

button to set the analog

outputs.
Once the output has been set, the imported value is normalized with decimal
places.

Click

[OK]

to end the test and close the window.

Alternatively, the inputs and outputs can also be tested with the help of the menu
option

Visualization > Process values

Содержание 761-214







































































































Результаты поиска

Содержание 761-214

Отзывы:

Похожие инструкции для 761-214

Бренды по названию

Популярные бренды

WAGO 761-214, Руководство пользователя

Результаты поиска

Содержание 761-214

Отзывы:

Похожие инструкции для 761-214

Бренды по названию

Популярные бренды