WAGO 750-610/040-000 Скачать руководство пользователя

Страница: 13 / 56

WAGO I/O SYSTEM 750 XTR

Important Notes

750-610/040-000 Power Supply 24 VDC Fuse Diagn XTR

Manual

Version 2.0.0

Power from SELV/PELV power supply only!

All field signals and field supplies connected to this XTR I/O module
(750-610/040-000) must be powered from SELV/PELV power supply(s)!

Before replacing the fuse, make sure there is no risk of explosion!

The fuse shall only be replaced when the system supply and the field supply are
switched off, or when the area is known to be non-hazardous.

Observe the maximum power dissipation and, if required, UL requirements!

Only use fuses with a maximum power dissipation of 1.6W (IEC 127). For UL-
approved systems, only use fuses with UL approval.

Do not touch hot surfaces!

The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.

Ensure proper contact with the DIN-rail!

Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed
contacts).

Содержание 750-610/040-000

























































Результаты поиска

Содержание 750-610/040-000

Отзывы:

Похожие инструкции для 750-610/040-000

Бренды по названию

Популярные бренды

WAGO 750-610/040-000, Руководство пользователя

Результаты поиска

Содержание 750-610/040-000

Отзывы:

Похожие инструкции для 750-610/040-000

Бренды по названию

Популярные бренды