Wacker Neuson IREN Скачать руководство пользователя страница 10

3 Security

10

100_0101_si_0010.fm

Avoid physical contact with grounded parts.

Do not use the protection hose, power cable or other components of the machine as a climbing aid 
or to secure transport.

Vibration-induced long-term damage cannot be ruled out during intensive use of hand-operated 
machinery. The respective statutory provisions and guidelines shall be observed.
The vibration emission value may differ from the declared value depending on the nature and manner 
in which the power tool is used.

3.9

Maintenance

The following notes must be observed:

This machine may not be maintained, repaired, adjusted or cleaned while switched on.

Adhere to maintenance intervals.

After each maintenance or repair, the safety devices on this machine must be reattached.

Observe the maintenance schedule. Identified work must be taken over by the service department of 
the Wacker Neuson contact partner.

Immediately replace worn or damaged machine parts. Only use spare parts from Wacker Neuson.

Keep the machine clean.

Missing, damaged, or illegible safety warning labels should be replaced immediately. Safety stickers 
contain important information for the protection of the operator.

Maintenance jobs must be carried out in clean and dry environment (e.g. in a workshop).

3.10

Personal Protective Equipment

NOTICE

To prevent personal injury when handling this machine, personal protective equipment 
must be worn when working on or around this machine.

Pictogram

Significance

Description

Wear safety shoes!

Safety shoes provide protection from bruises, falling 
objects, and slipping.

Wear protective gloves!

Protective gloves provide protection from abrasion, cuts, 
punctures, and hot surfaces.

Wear ear protection!

Ear protection provides protection from permanent 
hearing impairment.

NOTICE

With this machine, the permissible, country-specific noise limit (personal rating level) may 
be exceeded. Therefore, ear protection must be worn. For exact values regarding noise 
emissions, refer to 

Technical Data

 section.

When wearing ear protection, remain alert because your ability to hear noises such as 
screams or signal tones is restricted.

Wacker Neuson recommends always wearing ear protection.

Содержание IREN







































Отзывы: