Wabtec Ricon K2005 страница 31 Скачать руководство пользователя | Manualshive

Страница: 31 / 76

background image

3 - 2

MAINTENANCE

JUNE 2021

32DSKF02.D

TITANIUM S-SERIES AND K-SERIES

PUBLIC USE SERVICE MANUAL

C.

MAINTENANCE

SCHEDULE

Under normal operating conditions, maintenance inspections are required at least every six months (1750 cycles) and a
thorough inspection should be performed at service intervals referenced in

Table 3-1

. Service should be increased un-

der conditions of heavier use (more than 10 cycles per day).

TABLE 3-1: MAINTENANCE SCHEDULE

SERVICE POINT

ACTION TO PERFORM

10 CYCLES

Overall condition

Listen for abnormal noises as lift operates (i.e. grinding or binding noises.)

Control pendant

Verify that control pendant is undamaged and cable connector is tight.

Threshold
warning system

Verify that system properly detects objects in threshold area and actuates the audible alarm.

Bridgeplate load sen-
sor

Verify that sensor inhibits downward movement of platform when a weight is present on
lowered bridgeplate.

150 CYCLES

Electrical wiring

Inspect electrical wiring for frayed wires, loose connectors, etc.

Vehicle interlock

Place vehicle in non-interlock mode and verify that lift does not operate.

Decals

Verify that lift decals are properly affixed, clearly visible, and legible. Replace, if necessary.

Armrests

Verify that armrest fasteners are properly tightened.

Lift mounting points



Verify that vehicle mounting and support points are undamaged.



Verify that mounting bolts are sufficiently tight and free of corrosion.

Main lifting pivots

Verify that link pins on arms are properly installed, free from damage, and locked in position.

Platform pivot points

Verify that platform moves freely, without binding, and does not wobble.

Bridgeplate



Verify that bridgeplate operates without binding during lift functions.



Verify that bridgeplate deploys fully when platform stops at floor level.



Verify bridgeplate rests flat against baseplate.

Front rollstop



Verify that rollstop is opened completely when platform is at ground level.



Verify that rollstop closes and locks when platform leaves ground.

Hydraulic power unit

CAUTION

Check and add fluid when platform is at ground level. Fluid that is added when platform is

raised will overflow when platform is lowered.



Verify that pump hydraulic fluid level is at FULL mark when platform is at ground level.
Add Texaco 01554 Aircraft Hydraulic Oil or equivalent U.S. mil spec H5606G fluid.



Verify there are no hydraulic fluid leaks.



Verify that manual backup pump operates properly.

1800 CYCLES

Cleaning and
lubrication

1. Clean lift with mild soap and water and wipe dry. Prevent rust by coating all surfaces

with a light weight oil. Remove excess oil.

2. Spray penetrating oil (Curtisol



Red Grease 88167 or WD-40



) where specified follow-

ing directions on container. Remove excess grease from surrounding areas.

CAUTION

A Ricon dealer or qualified service technician must perform the following safety check.

3600 CYCLES

Hydraulic cylinder,
hoses and fittings



Check hydraulic cylinder for evidence of leaks.



Inspect hydraulic hoses for damage.



Verify that all fittings are tight.

END OF TABLE

«
...
29
30
31
32
33
...
»

Содержание Ricon K2005













































































Отзывы:

Нет отзывов

Похожие инструкции для Ricon K2005

Бренд: CAME Страницы: 12

POWER TIG 210EXT

Бренд: R-Tech Страницы: 27

Productivity 2000 P2-08NAS

Бренд: Automationdirect.com Страницы: 4

Бренд: FAAC Страницы: 16

StorageWorks DS-BA35X-MN

Бренд: Digital Equipment Страницы: 2

Бренд: Acard Страницы: 2

Rotational R-450A

Бренд: Global Lift Страницы: 49

Бренд: R. Beck Maschinenbau Страницы: 40

Бренд: ELS LIFT Страницы: 36

Бренд: OSTBERG Страницы: 69

Бренд: BACKSAFE Страницы: 27

Бренд: FOG Страницы: 72

Бренд: Würth Страницы: 292

Бренд: Hong Kong Easyweld Limited Страницы: 18

Бренд: IFM Electronic Страницы: 15

Бренд: Lampert Страницы: 24

Бренд: Kemppi Страницы: 27

Бренд: Palfinger Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды