manualshive.com logo in svg

Wabtec Ricon K2005, Руководство по обслуживанию

Поделиться
Скачать
Wabtec Ricon K2005 Скачать руководство пользователя страница 32

3 - 3 

MAINTENANCE 

JUNE 2021

 

32DSKF02.D

 

TITANIUM S-SERIES AND K-SERIES 

PUBLIC USE SERVICE MANUAL 

D.

TROUBLESHOOTING

The troubleshooting guides are designed to provide logical starting points to locate general problems that could occur
with lift.  However, not all possible problems or combinations of problems are listed.  For troubleshooting lift, refer to

Tables 3-2

.  The guide do not incorporate routine safety precautions or preliminary procedures and assume that vehicle

battery is fully charged and battery terminals/connectors are clean and tight.

         WARNING 

THE TROUBLESHOOTING GUIDES DO NOT INCORPORATE ROUTINE SAFETY 

PRECAUTIONS OR PRELIMINARY PROCEDURES.  DURING THE RICON WARRANTY 

PERIOD A TRAINED, RICON DEALER OR QUALIFIED SERVICE TECHNICIAN MUST 

PERFORM TROUBLESHOOTING.  AFTER THE WARRANTY PERIOD, IT IS RECOMMENDED 

THAT TROUBLESHOOTING BE CONTINUED BY A QUALIFIED SERVICE TECHNICIAN.

 

1.

LIFT 

TROUBLESHOOTING

TABLE 3-2:  TROUBLESHOOTING LIFT OPERATION  

SYMPTOM

 

POSSIBLE CAUSE

 

REMEDY

 

Hydraulic fluid leaks

 

Loose hydraulic fitting.

 

Make sure fitting is PROPERLY tightened.

 

Hydraulic component 
defective.

 

Discontinue use of lift.  Have repairs made by a Ricon deal-
er or qualified service technician.

 

Rollstop does not open

 

Obstruction of rollstop 
release latch.

 

Raise lift and remove obstruction.

 

Lift  
functions

 

Abnormal  
Operation.

 

Obstruction in lifting frame.

 

Remove obstruction and check for any damage

 

Backup pump manual release 
valve OPEN.

 

Turn manual release valve CLOCKWISE until slightly snug.

 

Hydraulic fluid may be low.

 

While platform is at GROUND LEVEL, be certain that pump 
hydraulic fluid level is maintained at required FULL level.  
Add only Texaco 01554 Aircraft Hydraulic Oil or equivalent 
U.S. mil spec H5606G fluid.

 

Air may be trapped in  
hydraulic system. 

Purge hydraulic system by operating lift through its maxi-
mum range of travel for at least four complete cycles. (For 
vehicles that do not use full travel of lift, the maximum range 
of travel is accomplished by raising vehicle on a service 
hoist or ramp.)

 

No Operation.

 

Control system circuit breaker 
tripped.

 

Reset circuit breaker.

 

Backup pump manual release 
valve OPEN.

 

Turn manual release valve CLOCKWISE until slightly snug.

 

Hydraulic hose or fitting leak.

 

Contact a Ricon dealer or qualified service technician for re-
pair.

 

Hydraulic fluid may be low.

 

While platform is at GROUND LEVEL, be certain that pump 
hydraulic fluid level is maintained at required FULL level.  
Add only Texaco 01554 Aircraft Hydraulic Oil or equivalent 
U.S. mil spec H5606G fluid.

 

Air can be trapped in 
hydraulic system. 

Purge hydraulic system by operating lift through its maxi-
mum range of travel for at least four complete cycles. (For 
vehicles that do not use full travel of lift, the maximum range 
of travel is accomplished by raising vehicle on a service 
hoist or ramp.)

 

END OF TABLE

 

Содержание Ricon K2005













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды