37
4.
Specifications regarding the machine
4.6
Electrical equipment (1.4 kW)
The main drive motor (single phase series-wound motor) is supplied already installed
■
The main spindle drive has an ON/OFF switch with under-voltage trigger.
■
The ON/OFF switch must also be switched on again after the power is interrupted.
■
In the event of the drive motor being overloaded, it will switch itself off automatically. The drive motor
can only be switched back on again after a short waiting period
4.7
Electrical equipment (2.0 kW)
■
The machine has a 3-setting switch (START RIGHT - STOP - START LEFT)
■
The under-voltage trigger is integrated in the electronics of the motor
■ In order to start the machine or restart after the power has been interrupted, first switch the 3-setting
switch to the „STOP“ position.
■
The switch must remain on „STOP“ for approximately 10 seconds to enable the motor to reset.
■
To change the direction of rotation of the main drive motor, the switch must rest on „STOP“ for about
1 second to allow the relays on the control board enough time to switch.
■
In the event of the main drive motor being overloaded, it will switch itself off automatically. The main
drive motor can only be switched back on again after a short waiting period.
5.
Achieving optimum results
and avoiding incorrect usage
■
Use of suitable processing tools.
■
Adaptation of revolution setting and feed to the material and workpiece.
■
Clamp the tool in such a way that the clamping point is as close to the workpiece as possible.
■ Clamp the workpieces firmly and without vibrations.
■
The use of coolant and lubrication to increase the durability of the tool, improve surface quality and
accuracy.
■
Clamp processing tools and workpieces on a clean clamping surface.
■ Lubricate machine sufficiently.
■
Set the bearing clearance and guides correctly.
Содержание CC-F1410 LF hs
