WABCO ABS Скачать руководство пользователя

Страница: 29 / 122

Diagnostics, Troubleshooting and Testing

WABCO

Maintenance Manual MM-0112 (Revised 07-18)

Modulator Valve Testing

Electrical Checks

앫

Check modulator valve by itself for resistance. Figure 3.1

and

Figure 3.17.

앫

Check ECU harness and modulator valve together for resistance.
Figure 3.18 and Figure 3.19.

앫

Verify no change in resistance or open circuit between valve by
itself and through harness.

앫

Check harness by itself for any shorts to battery and shorts to
ground.

앫

Measurements should read as follows:

NOTE:

If resistance exceeds 9.0 ohm for 12V system (21.0 ohm for

24V system), verify the reading was not taken between the inlet and
outlet. If the correct pins were tested, clean the electrical contacts at
the modulator and retest.

Figure 3.16

Figure 3.17

Frame-Mounted

With ESC

X2-Green

17 and 18

X2-Green

5 and

X3-Green

1 and 2

X3-Green

3 and 4

LR (3rd axle)

X4-Brown

3 and 4

RR (3rd axle)

X4-Brown

5 and

Location

Measurement

Inlet valve pin to Ground

4.0-9.0 ohm for 12V system

11.0-21.0 ohm for 24V system

Outlet valve pin to Ground

4.0-9.0 ohm for 12V system

11.0-21.0 ohm for 24V system

At ECU harness pins with
modulator valve connected

Same as above, no more than 1
ohm difference

ECU harness by itself for battery
voltage or ground

No continuity

ECU

Sensor

Connector

Pins

Figure 3.1

Figure 3.17

BAYONET-STYLE CONNECTOR

4004022a

EXHAUST SOLENOID
(BLUE WIRE)

INLET SOLENOID
(BROWN WIRE)

ROUND TERMINAL

OPEN-STYLE CONNECTOR

ROUND

TERMINAL

EXHAUST SOLENOID
(BLUE WIRE)

INLET SOLENOID

(BROWN WIRE)

4004021a

Содержание ABS



























































































































Результаты поиска

Содержание ABS

Отзывы:

Похожие инструкции для ABS

Бренды по названию

Популярные бренды

WABCO ABS, Руководство по обслуживанию

Результаты поиска

Содержание ABS

Отзывы:

Похожие инструкции для ABS

Бренды по названию

Популярные бренды