background image

VCW & VCD SERIES CHIP WARMER 

 

F-38053 (08-14) 

 

 

GENERAL 

 

INTRODUCTION 

 
Vulcan Chip Warmers are produced with 
quality workmanship and material. 

 

Proper installation, usage, and 
maintenance of your warmer will result 
in many years of satisfactory 
performance. 
 
It is suggested that you thoroughly read 
this entire manual and carefully follow all 
of the instructions provided. 
 

 
As with any piece of food service 
equipment, this Chip Warmer requires a 
minimum of care and maintenance. 

 

Recommended procedures are 
contained in this manual and should 
become a regular part of the operation 
of the unit. 
 
 
 
 

INSTALLATION (ALL MODELS

 

Before installing, verify that the electrical 
service agrees with the specifications on 
the rating plate located on the lower 
back corner of the warmer.  If the supply 
and equipment requirements do not 
agree, do not proceed with unpacking 
and installation.  Contact your Vulcan 
Customer Service Department 
immediately.  

(Page 11) 

 
UNPACKING:

 

The Warmer was inspected before 
leaving the factory.  The transportation 
company assumes full responsibility for 
safe delivery upon acceptance of the 
shipment.  Immediately after unpacking, 
check for possible shipping damage to 
the warmer. 

If the warmer is found to be 
damaged, save the packaging 
material and contact the carrier 
within 15 days of delivery. 

 
 
Carefully unpack warmer and place in a 
work accessible area. 
 
 

 
1. 

Remove banding holding the 

 

carton to the pallet. 

2. 

Carefully remove warmer from 

 

carton and place on floor or table. 

3. 

Remove any and all packaging 

 

materials inside unit. 

4. 

Peel off all vinyl protection 
film

5. 

Thoroughly clean the warmer 
as 

 

described in the 

cleaning instructions in this 
manual

 

LEGS INSTALLATION: 

To install legs, carefully tip Chip Warmer 
onto its side.  Screw legs into pre-drilled 
holes.  Return warmer to the upright 
position. 

 

LOCATION: 

For efficient warmer operation, choose a 
location that will provide easy loading 
and unloading without interfering with 
the final assembly of food orders. 
 
The installation location must allow 
adequate clearances for servicing and 
proper operation. 

Содержание ML-138037





























Отзывы: