background image

VCW & VCD SERIES CHIP WARMER 

 

F-38053 (08-14) 

 

 

 

OPERATION INSTRUCTIONS (Models VCW26 & VCW46) 

 

The Chip Warmer should be thoroughly 
cleaned before initial use. 
 

 

The Warmer and its 

parts are hot.  Be very careful when 
operating, cleaning, or servicing the 
warmer. 

 
1. 

Verify that the Chip Warmer is 

 

connected to the correct power 

 source. 
 
2. 

The Lighted Power Switch is 

 

located on right back side of the 

 

Chip Warmer.  Switch power 

 

switch to ON position.  Verify that 

 

the switch illuminates.  

(Fig. 6) 

 

 

 

POWER SWITCH 

 

(Fig.6) 

The power switch is what turns the 
unit on and off. 

 
3. 

The Thermostat knob is located 
in the back of the unit near the 
power switch.  

(Fig.7) 

 

 

 

 

    THERMOSTAT KNOB 

 

(Fig.7) 

 
Adjust the knob to the desired 
temperature setting.  Once a desired 
temperature setting is determined, the 
knob can be left in this position until a 
temperature adjustment is needed. 
 
4. 

Check the interior rear of warmer 
to ensure that it is heating.  The 
blower fan circulates heated air 
through the perforated removable 
baffle located at the bottom of the 
interior of the cabinet (under the 
chips.) 

(Fig. 10)

 

 
5. 

Open Top Doors. 

 
6. 

Pour chips into unit. 

 

Do not overfill.  The Top Doors must 
be able to fully close. 
VCW26 holds approx. 26 gallons and  
VCW46 holds approx. 46 gallons of 
chips. 
 

7. Close 

Top 

Doors. 

 
8. 

After approx. 30 to 40 minutes, 

 

open Front Door to access 

 warmed 

chips. 

 
9. 

Close Front Door after access. 

 

SHUTDOWN 

 

 The Warmer and its 

parts are hot.  Be very careful when 
operating, cleaning, or servicing the 
warmer. 

At the end of the day: 

1. Switch Power Switch to OFF 

position.  

2. Clean unit following instructions 

in this manual. 

Содержание ML-138037





























Отзывы: