EN
13
WWW.VONROC.COM
Avoid dust accumulation at the workplace.
Dust can easily ignite.
The dust extraction system can be blocked by dust,
chips or fragments of the workpiece. Thus, it must
be cleaned regularly. To do so:
1. Disconnect the mains plug from the power
supply.
2. Wait until the saw blade has come to a complete
stop.
3. Remove any blockage if necessary
Mounting the dust bag (Fig. A, B)
Press in the clamp of the dust bag (26) and slide
it onto the dust outlet (28) on the back of the ma-
chine. The dust bag stays in place when releasing
the clamp.
Connecting a vacuum cleaner (Fig. A, B, T)
The dust extractor must be suitable for the
material being worked.
When vacuuming dry dust that is especially
detrimental to health or carcinogenic, use a
special dust extractor.
A vacuum cleaner hose can be connected to the
dust outlet (28). To do so, simply connect the vacu-
um hose to the dust extraction spout.
4. OPERATION
Before you turn on the machine, always
check that the saw blade is fitted correctly.
The blade must turn smoothly.
Always check the protective guards before
use.
For all cuts, it must first be ensured that the
saw blade at no time can come in contact
with the fence, workpiece clamp or other
machine parts. Remove any mounted
auxiliary stops or adjust them accordingly.
Supporting the workpiece (Fig. A, G)
Workpieces must always be properly supported.
The table extensions (10) can be extended left and
right to support a workpiece. To do so:
• Move the table extension (10) to the desired
position;
• Rotate the knob for table extension (8) inwards
or outwards until the table extension is posi-
tioned level on the work surface.
When sawing extra-long workpieces, the free end
of long workpieces must have something addition-
ally placed underneath it or be supported.
Clamping the workpiece (Fig. G)
Workpieces must always be firmly clamped. The
workpiece clamp (21) can be placed left and right
of the workpiece. To do so:
1. Ensure the workpiece is firmly pressed against
the fence (9);
2. Insert the supplied workpiece clamp (21) into
one of the holes intended for this purpose, as
can be seen on figure G;
3. Adjust the threaded rod of the workpiece clamp
(21) to the workpiece height;
4. Firmly tighten the threaded rod of the work-
piece clamp (21) to fix the workpiece in place.
To loosen, simply untighten the threaded rod of
the workpiece clamp (21).
The knob for workpiece clamp (44) can be used
to more quickly adjust the height of the workpiece
clamp (21). After adjusting the height, always firm-
ly tighten the threaded rod of the workpiece clamp
(21) to fix the workpiece in place.
Adjusting the fence (Fig. G)
Always adjust the fence to the specific type
of cut.
When sawing mitre and/or bevel angles, you have
to move the adjustable fence (7) depending on
the cutting direction. This way, the workpiece is
always properly supported by the fence under each
condition. To do so:
1. Loosen the locking bolt for adjustable fence (35);
2. Adjust the fence according to the desired cut.
For mitre or straight cuts the fence has to be
moved inwards towards the blade (max 8 mm)
without touching it. For bevel cuts, the fence
has to be moved outwards away from the blade
(max 8 mm) without touching it;
3.
Tighten the locking bolt for adjustable fence (35);
4. To ensure the blade won’t get in touch with the
adjustable fence (35), it is advised to make a
test run of the movement of the blade, without
turning the machine on.
Содержание MS506AC
