Volvo ECR 58 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 41

Volvo ECR 58 Скачать руководство пользователя страница 9

© Rototilt Group AB

2018-03-16

Indicator Rod - Open

EN

English

When Rototilt® is pressurised

hydraulically the quick coupler locking

function is opened. The indication on the

quick coupler shows that the lock is open.

When the quick coupler’s locking wedge/

locking bolts are fully open, the tool can

be detached by slowly retracting the

bucket cylinder.
Return the switch to its original position

to close the lock.
Pressurising is conducted for a preset

time, maximum 12 seconds.The selected

time can be checked on the display,

Menu settings

.

The switch must be switched on and then

off again to repressurise the hydraulic

cylinder.

A warning is shown on the display if the

quick coupler is in the open position.
The base machine/excavator can be

equipped with different combinations

of quick coupler and machine coupler.

The figure and text on the display are

dependent on the combination.
Both the quick coupler and the machine

coupler are available with and without

electronic monitoring (SecureLock).

2200397_ _6909

«
...
7
8
9
10
11
...
»

Содержание ECR 58










































Отзывы:

Нет отзывов