Volvo ECR 58 Скачать руководство пользователя страница 12

Страница: 12 / 41

2018-03-16

1. Remove Rototilt® from

Boom Harness

2. Demount Safety Plug

3. Connect Safety Plug to

Boom Harness

4. Protect empty connector.

English

Detach Rototilt®

Always park the tiltrotator on a stable and

flat surface, without the tool. Make sure

that Rototilt® cannot tip over.
Disconnect the hydraulic hoses and

harness between the Rototilt® and the

base machine/excavator. The tiltrotator

is now detached from the base machine/

excavator.
If the machine coupler/quick coupler

(excavator) is open while the harness to

the tiltrotator is still connected, a warning

is shown on the display.

Safety plug

The function is used to lock the machine

coupler/quick coupler (excavator) while

the tiltrotator is mounted. The lock pre-

vents accidental opening of the machine

coupler/quick coupler (excavator).
Disconnect the Rototilt® contact.
Remove the safety plug and connect it to

the boom harness contact.
Control of the machine coupler/quick

coupler (excavator) works normally again.

Operating extra hydraulics

Detach Rototilt®.

Now select regulation of extra hydraulics

on the display by activating double feeder.

Confirm with the OK function key.

For return to Rototilt ® control: First

connect the tiltrotator and then connect it

to the base machine/excavator.

Now select Rototilt® operation on the

display and confirm the selection with

the green function key and then the OK

function key.

Control of the oil flow in the base

machine/excavator’s extra hydraulics

circuit can be performed using a roller

or switch. Both options work in parallel

with any pedals on the base machine/

excavator.
Roller for the tilt function B regulates the

flow in both directions.

2200397_ _6909

Содержание ECR 58










































Результаты поиска

Содержание ECR 58

Отзывы:

Volvo ECR 58, Перевод оригинальной инструкции, Страница: 12 / 41

Результаты поиска

Содержание ECR 58

Отзывы: