Volvo Penta D16 Скачать руководство пользователя страница 58

Страница: 58 / 90

Drive belt, check and change

WARNING!

Stop the engine before doing any maintenance work.

General

Check belts after operation while they are still hot. It
should be possible to depress an alternator belt or
drive belt around 3–4 mm (0.012–0.016") between
pulleys.

IMPORTANT:

Always replace a belt that appears worn or is cracked.
Belts working in tandem must be replaced
simultaneously.

Both the alternator belts and drive belt have automatic
belt tensioners and should not need adjusting.

Drive belt, water pump, replacement

1 Switch off the manin switch(es) and check that the

engine is not connected to system power.

2 Remove the belt cover.

3 Use a 1/2 inch socket to lower the belt tensioner (

)

and release the belt.

4 Remove the drive belt.

5 Check that the pulleys are clean and undamaged.

6 Lower the belt tensioner (

) and install the new

drive belts.

7 Install the belt guards.

8 Start the engine and do a function check.

Alternator belt, replacement

1 Switch off the manin switch(es) and check that the

engine is not connected to system power.

2 Remove the belt cover.

3 Remove the water pump drive belt (refer to the

Water pump drive belt, replacement

section).

4 Use a 1/2 inch socket to raise the belt tensioner (

)

and release the alternator belt.

5 Remove the alternator belt.

6 Check that the pulleys are clean and undamaged.

7 Raise the belt tensioner (

) and install the new

alternator belt.

8 Re-install the water pump drive belt.

9 Install the belt guards.

10 Start the engine and do a function check.

P0006336

Maintenance

47711740 05-2019 © AB VOLVO PENTA

Содержание D16



























































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Volvo Penta D16, Руководство оператора

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды