Volvo Penta D16 Скачать руководство пользователя страница 61

Страница: 61 / 90

Oil Filter/By-pass Filter, Change

Change the oil filters and by-pass filter at every oil
change.
Remember to bring the old filters to an authorized
recycling station.

WARNING!

Hot oil and hot surfaces can cause burns.

1 Put a suitable vessel underneath the filters to avoid

oil spill.

2 Clean the filter bracket.

3 Unscrew the bypass filter (

) and the oil filters (

)

with a suitable filter wrench.

4 Make sure the seal's mating surfaces on the filter

brackets are clean.

5 Lightly oil the rubber seal of the new filters.

6 Mount the new filters by hand until the gasket is in

contact with the sealing surface. Then tighten the
filters another 3/4 to 1 turn.

7 Start the engine (idle) and make sure that no

leakages occur. Check the oil level once the engine
has stopped.

Maintenance

47711740 05-2019 © AB VOLVO PENTA

Содержание D16



























































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Volvo Penta D16, Руководство оператора

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды