Volvo Penta D16 Скачать руководство пользователя страница 26

Страница: 26 / 90

Settings

Serial number and software version

In order to see the engine serial number and software
version installed go to the main menu.
Press the Enter button (

) and hold it down and press

the Page button (

) at the same time.

The system returns automatically to the main menu.

Backlighting

Panel backlighting is adjusted in the info menu.
Press the Enter button (

) and hold it down; adjust

backlighting with the up/down buttons.

Contrast is adjusted in the main menu. Press the Enter
button (

) and hold it down; adjust the contrast with the

up/down buttons.

Changing language

Setting the language the information on the screen will
be shown in. There are six languages to choose from.

1 Press the Enter button (

) and hold it down to reach

the info menu. Press the Page button (

2 Browse using the up/down buttons.

3 Press Enter (

) to select the language and close the

menu.

Setting password

The password consists of 1–4 numerals.
The default password is 0 on delivery.

1 Navigate to the Adjustments menu.

2 Browse to “Password” using the up/down buttons.

Press Enter (

) to confirm the selection.

3 Browse using the up/down buttons to “Enter

Password” where 0 is shown. Press Enter (

) to

confirm the selection.

4 Exit the menu by pressing Page (

The password gives full access to the MCU.
Parameters may only be changed by trained
personnel.

Instruments and Controls

47711740 05-2019 © AB VOLVO PENTA

Содержание D16



























































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Volvo Penta D16, Руководство оператора

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды