Volvo Penta D16 Скачать руководство пользователя страница 44

Страница: 44 / 90

Extra Supply Fls

Auxiliary supply
Overcurrent protection for the auxiliary supply has tripped.

• Check the auxiliary stop connections for short circuits.

Reset the system by switching the main switch off and on.
Contact a Volvo Penta workshop if the fault remains.

ExtSTOP Active Fls

Emergency Stop Switch

• Check emergency stop button if any. Reset if necessary.

Fls

Miscellaneous system faults
Engine performance can be affected.Several possible causes of engine problems are described below.

• Battery voltage incorrect

Check belt tension. Refer to

Drive belt, check and change, page 56

Check battery fluid level. Refer to

Battery, page 74

• Fuel pressure incorrect.

Engine performance can be affected.

• Communication failure

Gear automatically set to neutral. Engine performance can be affected.

• Oil pressure too low.

Engine power is reduced.
Check the oil level in the engine. Refer to

Oil level, checking and topping up, page 57

Check that no leakage occurs.

• Sensor failure

Contact a Volvo Penta workshop if the fault remains.

Fls Throttle In

Engine speed demand to system lacking

• Check Control Lever

FuelDelPress Wrn

Fuel pressure too low.

• Check fuel level.

• Check that the fuel filters are not blocked. Replace filters if necessary. Refer to

Engine Fuel Filter

Replacement, page 62

• Check for fuel leakage.

Fault Code Register

47711740 05-2019 © AB VOLVO PENTA

Содержание D16



























































































Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды

Volvo Penta D16, Руководство оператора

Результаты поиска

Содержание D16

Отзывы:

Похожие инструкции для D16

Бренды по названию

Популярные бренды