manualshive.com logo in svg

Volvo Penta 3.0GL-B, Руководство оператора

Поделиться
Скачать
Volvo Penta 3.0GL-B Скачать руководство пользователя страница 76

74

7741591 / 2003-12

Power trim/tilt fluid level

The power trim and tilt assembly contains an electric motor, hy-
draulic pump, and reservoir.

At the beginning of each boating season, check the fluid level
in the reservoir:

1.

With the drive unit trimmed in as far as possible, remove

the fill cap.

2.

Check the fluid level. It should be between the minimum

and maximum marks on the reservoir. If needed, add Volvo
Penta DuraPlus Power Trim/Tilt and Steering Fluid.

3.

Replace the fill cap and tighten securely.

Steering reservoir fluid level

Whenever you check the engine oil, also remove the steering
reservoir dipstick and check the fluid level. Wipe the dipstick
and note the “hot” and “cold” fluid levels. If needed, add Volvo
Penta DuraPlus Power Trim/Tilt and Steering Fluid. Do not
overfill the pump reservoir.

CAUTION!

Never fill the steering system with an oil of unknown
quality. Non-recommended oil may cause steering op-
eration impairment, or component damage.

Do not allow contaminants to enter the reservoir when check-
ing or filling the oil level.

Primary shaft spline and bearing lubrication

The primary universal joint shaft splines and bearings 

must 

be

lubricated each year and whenever the drive unit is removed.
This procedure requires the removal of the drive unit; there-
fore, your Volvo Penta dealer should do it. An ideal time to
have this done is during the winterization process. Failure to
have primary shaft splines and bearings lubricated each year
may result in damage to the drive unit.

Tie rod (twin installations only)

Check the rod connecting the drive units, particularly if you hit
an obstacle. If the tie rod is bent, loose, or damaged, have it
serviced immediately by your Volvo Penta dealer. In the mean-
time, operate your boat at slow speeds only.

WARNING!

The tie bar is an integral part of the steering system
and is a vital safety part. A damaged tie rod may hinder
steering operation or render it completely ineffective.
Always replace a damaged tie bar. Never try to
straighten or weld a damaged tie rod.

 Maintenance

7741591 - Downloaded from www.volvopenta.com 12/03/2014 09:32:39

Содержание 3.0GL-B













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды