Vollrath Stoelting Flavor Burst STL-80SS-DLX Скачать руководство пользователя страница 68

Страница: 68 / 80

3. Select the syrup flavor you wish to use, then

place the bag on the table with the fitment
up and remove the dust cap.

4. Lifting up with the bag fitment, press the

center pin of the bag fitment valve and
gently press on the bag to release any
excess air.

5. Select a numbered tray to correspond with

the flavor you have chosen.

6. Grip the bag underneath the fitment and lift

the bag up, with your other hand supporting
the bottom of the bag. Flip the fitment end
over into the open end of the tray, while
guiding the back end of the syrup bag into
the back end of the syrup tray.

7. Settle the bag into the tray evenly, with the

fitment behind the tray opening.

8. Make sure the syrup bag is settled neatly

into the tray, and then install the loaded tray
into the cabinet.

9. At this time, you may wish to change the

Touch Panel menu flavor names to
coordinate with the new flavors installed.
This may be done now or later in the
TOUCH PANEL OPERATIONS MANUAL.

10. Perform the entire Clean-In-Place

procedure as instructed in the SCHEDULED
MAINTENANCE section. The Clean-In-
Place procedure

MUST

be done during the

initial setup of the STL-80SS-DLX to ensure
all the parts and syrup lines are sanitized
and ready for use.

Содержание Stoelting Flavor Burst STL-80SS-DLX

















































































Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Руководство оператора

Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды