Vollrath Stoelting Flavor Burst STL-80SS-DLX Скачать руководство пользователя страница 22

Страница: 22 / 80

Electronic Parts and Connections (See Figure 7)

ITEM PART

NO.

DESCRIPTION

QTY.

FUNCTION

1 STOEELE906

FLAVOR 10 COLOR TOUCH
PANEL

Control system for the unit.

2 STOEMIS3214

TOUCH PANEL MOUNTING
BRACKET ASSEMBLY

Secures the Touch Panel to the freezer.

2A STOEMIS3214A

TOUCH PANEL MOUNTING
PLATE

1 ea. Attaches the Touch Panel to the anchor bracket.

2B STOEMIS3214B

MOUNTING ANCHOR BRACKET

1 ea. Allows the bracket to be angled up or down.

2C STOEMIS3214C

MOUNTING BASE PLATE

1 ea. Creates a mounting base for the bracket assembly.

2D STOEFAS2170

M4 X 8 PHILLIPS SCREW

4 ea. Secures the mounting plate to the Touch Panel.

2E STOEFAS2174

1/4 - 20 NYLON LOCK NUT S.S.

2 ea. Secures the anchor bracket in a fixed position.

2F STOEMIS3076

ADHESIVE PAD

1 ea. Secures the mounting bracket to the freezer.

2G STOEFAS2172

1/4-20 X 1/2 HEX BOLT

2 ea. Hinges the Touch Panel plate and anchor bracket.

2H STOEFAS2023

MOUNTING BRACKET KNOB

4 ea. Secures the anchor bracket to the base plate.

STOEFAS2171

M4 LOCK WASHER

4 ea. Secures the connection between screw and plate.

2J STOEFAS2173

FLAT WASHER 18-8 S.S.

2 ea. Secures the connection between bolt and nut.

3 STOEELE650C

ELECTRONICS BOX COVER

Encloses the electronics board inside the
electronics box.

4 STOEELE650B

ELECTRONICS BOX BASE

Mounting panel for the electronics board.

5 STOEELE525M

MALE TO MALE 48” SWITCH
EXTENSION

Connects Touch Panel to the freezer switch.

6 STOEMIS3217

OPEN-CLOSE BUSHING 5/8”

Protects the cable harness.

7 STOEFAS2014

8-32 X 1/2" PAN HEAD

Secures various parts within the electronics box.

8 STOEFAS2040

6-32 x 1/4” TAPPING SCREW

Secures the cover of the Electronics Box.

9 STOEFAS2012

8-32 x 1/4” COUNTERSINK
SCREW

Protects power cables from liquids.

10 STOEELE485CTP

120V POWER ENTRANCE
MODULE

Provides power connection to outside of cabinet.

11 STOEELE932DLX

PUMP & SANITIZER CABLE
HARNESS – CTP DLX

Provides power to the syrup and sanitizer pumps.

12 STOEELE933

POWER SUPPLY JUMPER CABLE

Connects power supply to electronics board.

13 STOEELE931

EXTERNAL ROTOR CABLE

Connects drive motor to the back of cabinet.

14 STOEINJ330TS

INJECTOR MOTOR ASSEMBLY

Supplies power to Motor to turns gears.

15 STOEELE911

ELECTRONICS BOARD

Provides power to the system.

16 STOEELE650A

CTP-DLX ELECTRONICS BOX
COVER PLATE

Converts old electronics board opening into ports
for harness cable and rotor connection.

17 STOEFAS2035

8-32 NUTS - EXT. LOCK WASHER

Secures Electronics Board to the Box and the
Electronics Box to the cabinet.

18 STOEMIS3026S

TOUCH PANEL CABLE CASING

Conceals and protects the Touch Panel cable, as
well as attaches it to the freezer.

19 STOEELE930

INTERNAL ROTOR CABLE

Connects the drive motor to the back of the
cabinet.

20 STOEMIS3004

CTP ETHERNET CABLE PLATE

Converts the touchscreen cable hole to an
ethernet cable hole.

21 STOEMIS3216

CLOSURE PLUG 5/8 INCH

Closes up extra opening in the base panel.

22 STOEELE434

POWER CABLE

Supplies the electronics board with power.

23 STOEELE927

RJ45 ETHERNET CABLE GLAND

Secures the Ethernet cable to the cabinet.

Содержание Stoelting Flavor Burst STL-80SS-DLX

















































































Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Руководство оператора

Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды