Vollrath Stoelting Flavor Burst STL-80SS-DLX Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 80

background image

50

ADDITONAL PRODUCTS & SUPPLIES
REQUIRED:

- ENVIROKLEEN NO-RINSE CLEANER &
FOOD CONTACT SANITIZER

- STERA-SHEEN® GREEN LABEL SANITIZER

- DAWN® DISH SOAP

- APPROVED, SERVICEABLE AND
SANITIZED TOOLS AND BRUSHES.

(CONTACT WHITE GLOVE SERVICE FOR
RECOMMENDED SUPPLIES)

NOTE:

CLEAN AND SANITIZE YOUR HANDS

BEFORE YOU PERFORM THE FOLLOWING
PROCEDURES.

NOTE:

INSPECT ALL WEAR ITEMS AND

REPLACE IF NECESSARY.

NOTE:

THE SYSTEM IS NOT TO BE USED

BY PERSONS (INCLUDING CHILDREN) WITH
REDUCED PHYSICAL, SENSORY OR
MENTAL CAPABILITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS
THEY HAVE BEEN GIVEN SUPERVISION OR
INSTRUCTION.

NOTE:

CHILDREN ARE TO BE SUPERVISED

WHEN USING THE SYSTEM AND SHALL
NOT PLAY WITH THE SYSTEM.

NOTE:

INSTALL THE SYSTEM WHERE

AMBIENT TEMPERATURES ARE BETWEEN
60 AND 80 DEGREES FAHRENHEIT FOR
CORRECT OPERATION.

NOTE:

INSTALL THE SYSTEM IN A

LOCATION WHERE ITS USE AND
MAINTENANCE IS RESTRICTED TO
TRAINED PERSONNEL.

Installing the Touch Panel and Mounting
Bracket

The Touch Panel is the control unit for the
Flavor Burst

®

system. Normal operating

functions are performed using the Touch Panel
and the freezer draw handle. The Touch Panel
is mounted to the top of the freezer with the
Touch Panel mounting bracket.

NOTE:

IF YOUR FREEZER HAS A

ROUNDED TOP, CONTACT WHITE GLOVE
SERVICE FOR ALTERNATE MOUNTING
KITS.

1. Prepare detergent water by mixing several

drops of Dawn

®

dish soap with a gallon of

warm water (108°F / 42°C).

2. Determine where you wish to mount the

Touch Panel. It is typically mounted in the
middle of the freezer, centered above the
middle spout on a multi-barrel freezer, or
centered above the spout with the Flavor
Burst assembly attached (as shown in these
instructions). Clean the top surface of the
freezer where the mounting bracket will be
attached, between the front edge and the
hopper with detergent water. Rinse the area
with warm water (108°F / 42°C) and dry with
a single service towel.

NOTE:

THE SURFACE MUST BE FREE

FROM DUST AND OILS OR THE ADHESIVE
WILL NOT CURE PROPERLY.

EQUIPMENT SETUP

«
...
51
52
53
54
55
...
»

Содержание Stoelting Flavor Burst STL-80SS-DLX

















































































Отзывы:

Нет отзывов

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренд: Hamilton Beach Страницы: 56

Бренд: Rachel Allen Страницы: 32

Бренд: Cafection Страницы: 55

Бренд: DeLonghi Страницы: 18

Бренд: DeLonghi Страницы: 78

Nespresso BEC300

Бренд: Breville Страницы: 17

Бренд: iGenix Страницы: 12

60-CUP COFFEE URN

Бренд: Hamilton Beach Страницы: 15

ARNO KRUPS Nescafe Dolce Gusto KP10 Series

Бренд: SEB Страницы: 52

Бренд: Dolce Gusto Страницы: 20

Бренд: Chard Страницы: 8

Бренд: Hamilton Beach Страницы: 10

Бренд: Omcan Страницы: 16

Бренд: Quality Espresso Страницы: 47

Бренд: acaia Страницы: 31

ECAM44.62 Series

Бренд: DeLonghi Страницы: 41

Бренд: Hamilton Beach Страницы: 22

Бренд: Saivod Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды