Vollrath Stoelting Flavor Burst STL-80SS-DLX Скачать руководство пользователя страница 29

Страница: 29 / 80

Installing the Injector System

1. Install the spout adapter assembly,

complete with o-rings, onto the freezer
spout. Push up on the adapter with your
palm until it snaps on. Ensure it is evenly
and fully installed.

2. Place the Injector Assembly onto the

suspension bracket, so that the Gear Box
post slides into the bracket opening. Install
the Injector Head fully over the spout
adapter.

3. Push up on the Injector Assembly and lift

the locking collar up and over the adapter
tabs. Rotate the locking collar over the tabs
to secure.

4. Connect the Drive Motor cable to the Motor.

5. Ensure the Injector Assembly is resting level

and horizontal. Install and tighten the Gear
Box nut to secure the assembly.

6. Insert the syrup line manifold end fully into

the Injector Head syrup line opening.
Rotate it until motion stops to secure.

7. With a container under the dispensing

spout, press the FLUSH SPOUT key on the
Touch Panel to purge any remaining
product from the spout.

NOTE:

IF NO “FLUSH SPOUT” BUTTON IS

SHOWN ON THE SCREEN, YOU CAN
ACCESS THE KEY UNDER THE “FLUSHING
FUNCTIONS” SECTION OF THE
MAINTENANCE MENU.

Содержание Stoelting Flavor Burst STL-80SS-DLX

















































































Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды

Vollrath Stoelting Flavor Burst STL-80SS-DLX, Руководство оператора

Результаты поиска

Содержание Stoelting Flavor Burst STL-80SS-DLX

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-80SS-DLX

Бренды по названию

Популярные бренды