Vollrath Stoelting Flavor Burst STL-40BLD-JR Скачать руководство пользователя | Manualshive

Страница: 51 / 74

background image

48

NOTE:

YOUR HANDS SHOULD BE CLEANED

AND SANITIZED BEFORE YOU PERFORM
THE FOLLOWING PROCEDURES.

NOTE:

INSPECT ALL WEAR ITEMS AND

REPLACE IF NECESSARY.

NOTE:

THE FOLLOWING PROCEDURES

REQUIRE APPROVED, SERVICEABLE AND
SANITIZED TOOLS AND BRUSHES.
CONTACT WHITE GLOVE SERVICE FOR
RECOMMENDED SUPPLIES.

NOTE:

USE STERA-SHEEN® GREEN LABEL

SANITIZER AND DAWN® DISH SOAP MIXED
WITH WARM WATER (108°F / 42°C) FOR THE
FOLLOWING PROCEDURES. REFER TO
MANUFACTURER’S INSTRUCTIONS FOR
PROPER PREPARATIONS OF THESE
CLEANING AGENTS.

NOTE:

THE SYSTEM IS NOT TO BE USED

BY PERSONS (INCLUDING CHILDREN) WITH
REDUCED PHYSICAL, SENSORY OR
MENTAL CAPABILITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE, UNLESS
THEY HAVE BEEN GIVEN SUPERVISION OR
INSTRUCTION.

NOTE:

CHILDREN ARE TO BE SUPERVISED

WHEN USING THE SYSTEM AND SHALL
NOT PLAY WITH THE SYSTEM.

NOTE:

INSTALL THE SYSTEM WHERE

AMBIENT TEMPERATURES ARE BETWEEN
60 AND 80 DEGREES FAHRENHEIT FOR
CORRECT OPERATION.

NOTE:

INSTALL THE SYSTEM IN A

LOCATION WHERE ITS USE AND
MAINTENANCE IS RESTRICTED TO
TRAINED PERSONNEL.

Installing the Touch Panel and Mounting
Bracket

The Touch Panel is the control unit for the
Flavor Burst

®

system. Normal operating

functions are performed using the Touch Panel
and the freezer draw handle. The Touch Panel
is mounted to the top of the freezer with the
Touch Panel mounting bracket.

NOTE:

IF YOUR FREEZER HAS A

ROUNDED TOP, CONTACT WHITE GLOVE
SERVICE FOR ALTERNATE MOUNTING
KITS.

1. Prepare detergent water by mixing several

drops of Dawn

®

dish soap with a gallon of

warm water (108°F / 42°C).

2. Determine where you wish to mount the

Touch Panel. It is typically mounted in the
middle of the freezer, centered above the
middle spout on a multi-barrel freezer, or
centered above the spout with the Flavor
Burst assembly attached (as shown in these
instructions). Clean the top surface of the
freezer where the mounting bracket will be
attached, between the front edge and the
hopper with detergent water. Rinse the area
with warm water (108°F / 42°C) and dry with
a single service towel.

NOTE:

THE SURFACE MUST BE FREE

FROM DUST AND OILS OR THE ADHESIVE
WILL NOT CURE PROPERLY.

EQUIPMENT SETUP

«
...
49
50
51
52
53
...
»

Содержание Stoelting Flavor Burst STL-40BLD-JR











































































Отзывы:

Нет отзывов

Похожие инструкции для Stoelting Flavor Burst STL-40BLD-JR

Pane Express Top 131

Бренд: ARIETE Страницы: 206

Бренд: iCES Страницы: 55

Бренд: Melitta Страницы: 28

Бренд: CASO DESIGN Страницы: 158

Бренд: emerio Страницы: 26

Бренд: Buffalo Страницы: 56

Бренд: NewAir Страницы: 34

Бренд: Ice-O-Matic Страницы: 2

Бренд: Marta Страницы: 8

FLAVIA CREATION 600

Бренд: LAVAZZA Страницы: 36

Бренд: Brewmatic Страницы: 20

Бренд: Duronic Страницы: 56

Бренд: Saeco Страницы: 2

Бренд: Saeco Страницы: 44

Бренд: Polar Refrigeration Страницы: 40

Бренд: U-Line Страницы: 18

Бренд: U-Line Страницы: 44

Бренд: U-Line Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды