Vollrath Stoelting Flavor Burst STL-40BLD-JR Скачать руководство пользователя

Страница: 12 / 74

Cabinet – (See Figure 2)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

N/A

ELECTRONICS SYSTEM

Control system for the unit.

STOECAB135R-4-A

RIGHT SIDE PANEL - JUNIOR

Holds tray support brackets and panel brackets.

STOECAB145

TRAY SUPPORT BRACKET

Supports flavoring trays.

STOEFAS2024

8-32 X 1/4 PAN HEAD

Fastens panel brackets to divider panel, secures
sides.

STOEFAS2014

8-32 X 1/2" PAN HEAD

Attaches top panel, back cover, and feet to cabinet.

STOESYR944

SYRUP TUBE ASSEMBLY –
SOFT SERVE

Transports the flavoring from the syrup bag to the
syrup pump.

STOEELE932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer pumps.

STOEMIS3066

MINI BUSHING

Protects flush tube.

STOEMIS3028-80

FLUSH TUBE ASSEMBLY

Connects with flavor line to flush with sanitizer
solution.

10 STOECAB139-4

FRONT DOOR PANEL - JUNIOR

Provides easy access to syrup bags and
connectors.

11 STOECAB136-4-A

REAR PUMP COVER - JUNIOR

Back panel to cover pumps.

12 STOEFIX1023

3/16" X 3/16" BARB TUBE
CONNECT

Splices together flush tubes.

13 STOECAB134-4

DIVIDER PANEL - JUNIOR

Holds tray support brackets and divides flavor
trays.

14 STOECAB144R

RIGHT PANEL BRACKET

Holds tray support rails.

15 STOECAB144L

LEFT PANEL BRACKET

Holds tray support rails.

16 STOECAB143

LATCH BRACKET

Provides latching tab for front panel latch.

17 STOEFAS2001

FRONT DOOR PANEL LATCH

Latches front door to cabinet front.

18 STOESYR927-4

INTERNAL 5-TUBE ASSEMBLY
JUNIOR

Transports syrup from bags to flavor 9-Tube
Assembly.

19 STOESAN748

PERISTALTIC SANITIZER
PUMP

Pumps sanitizer solution to flush tube and sanitizer
line.

20 STOESYR307

PERISTALTIC SYRUP PUMP

Pumps syrup from flavor bags into flavor lines.

21 STOECAB155L-4

PUMP MOUNTING STRIP -
JUNIOR

Support for syrup trays and spacing between
panels.

22 STOECAB155R-4

PUMP MOUNTING STRIP -
JUNIOR

Support for syrup trays and spacing between
panels.

23 STOEFAS2037

TAPPED NYLON SPACER

Secures screw to center panel, and support for
trays.

24 STOEFAS2032

STANDARD NYLON SPACERS

Provides extra support for flavor trays.

25 STOEFAS2034

8-32 X 3/4" MACHINE SCREW

Attaches bushings to divider panel.

26 STOEMIS3067

OPEN/CLOSED BUSHING

Strain relief for internal 9-Tube Assembly.

27 STOEFIX1033

1/4" X 1/4" BLKHD (PUSH-TO-
CONNECT)

Connects sanitizer tank tube to the unit.

28 STOETUB803

TUBING-PER FOOT

Transports sanitizer solution from tank to pump.

29 STOECAB133

BASE PANEL

Attaches the bottom of the inner and side panels.

30 STOERUB618

RUBBER BUMPER WITH
WASHER

Provides spacing between cabinet base and table.

31 STOEFAS2035

8-32 NUT - EXT. LOCK
WASHER

Attaches to screw and holds rubber bumper in
place.

32 STOEMIS3074

SHORTY PLUG #1672

Covers screw hole in rubber bumper.

Содержание Stoelting Flavor Burst STL-40BLD-JR











































































Результаты поиска

Содержание Stoelting Flavor Burst STL-40BLD-JR

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-40BLD-JR

Бренды по названию

Популярные бренды

Vollrath Stoelting Flavor Burst STL-40BLD-JR, Руководство оператора

Результаты поиска

Содержание Stoelting Flavor Burst STL-40BLD-JR

Отзывы:

Похожие инструкции для Stoelting Flavor Burst STL-40BLD-JR

Бренды по названию

Популярные бренды