Vollrath Stoelting Flavor Burst STL-40BLD-JR Скачать руководство пользователя | Manualshive

Страница: 67 / 74

background image

64

3. Evaluate your serving for both appearance

and taste. Look and taste the serving to
ensure the syrup level is acceptable. Draw
servings of the other flavors to evaluate
their syrup dispensing levels.

NOTE:

ADJUST THE DISPENSE SPEEDS OF

THE FLAVORS IN THE “SETUP TRAYS AND
DISPENSE SPEEDS” SECTION OF THE
MAINTENANCE MENU.

NOTE:

YOU CAN ALSO ADJUST THE

FLAVOR STRENGTH IN A SERVING BY
SLOWING OR SPEEDING UP THE
FREEZER’S DRAW RATE.

4. If the timed servings setting is enabled,

draw different serving sizes and compare
them to see if the size of each serving is
what you expected.

NOTE:

CHANGE THE SERVING SIZE TIMES

IN THE “ADJUST DISPENSE TIME LIMITS”
SECTION OF THE MAINTENANCE MENU.

5. If the white cap option is enabled, see if

syrup product has cleared the Blending
Head. Make sure there is not too much
unflavored product at the top of your
serving.

NOTE:

ADJUST THE WHITE CAP TIME IN

THE “ENABLE OR DISABLE SERVING
OPTIONS” SECTION OF THE
MAINTENANCE MENU.

NOTE:

THE WHITE CAP OPTION IS

ONLY AVAILABLE WHEN TIMED
SERVING SIZES IS ACTIVATED.

6. Draw multi-flavored servings to evaluate if

the layer timing is what you expected. A
shorter dispense time results in narrower
layers; a longer dispense time results in
wider layers. You can fit more flavor
selections in a serving with narrow layers,
however, the layers may blend together.
Wider layers will show a more distinct color
and flavor difference between layers, but
will have limitations on how many flavors
can be dispensed in one serving.

NOTE:

ADJUST THE FLAVOR SELECTION

TIME IN THE “ENABLE OR DISABLE
SERVING OPTIONS” SECTION OF THE
MAINTENANCE MENU.

26284

NEEDS

LESS

AVERAGE

NEEDS

MORE

26289

SMALL

MEDIUM

EXTRA LARGE

LARGE

26576

TOO

MUCH
TIME -

Too much

unflavored

product

NOT

ENOUGH

TIME -

May result in

carryover

issues with

next serving

26292

WIDER

LAYERS

NARROWER

LAYERS

«
...
65
66
67
68
69
...
»

Содержание Stoelting Flavor Burst STL-40BLD-JR











































































Отзывы:

Нет отзывов

Похожие инструкции для Stoelting Flavor Burst STL-40BLD-JR

Бренд: Kees van der Westen Страницы: 66

Бренд: JDE Страницы: 15

PerfectCoffee MC06

Бренд: Waeco Страницы: 128

Бренд: Hoshizaki Страницы: 44

Бренд: Rangemaster Страницы: 48

Бренд: Saeco Страницы: 48

NAVIGLIO HD8749/01

Бренд: Gaggia Страницы: 48

Бренд: Taurus Страницы: 32

Mini-Cappuccino

Бренд: Newco Страницы: 24

Бренд: Kalorik Страницы: 26

Бренд: FAR Страницы: 60

Бренд: Gaggia Страницы: 76

Бренд: SPM Страницы: 76

Бренд: Philips Страницы: 24

Eccellenza Cafe

Бренд: VKI Technologies Страницы: 108

PROAROMA THERM FME1

Бренд: Krups Страницы: 38

PROAROMA THERM FMD1 Series

Бренд: Krups Страницы: 59

Бренд: Scotsman Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды