Volkswagen golf 2006 Скачать руководство пользователя страница 25

Страница: 25 / 93

Malfunctions found must be rectified (repair measure).

Brake linings front and rear, checking thickness

Special tools, testers and auxiliary items required

Torque wrench V.A.G 1332

Electric flashlight and mirror

Perform the following work procedure:

The adapter to loosen/tighten the anti-theft wheel bolts is
located in the vehicle tool kit

01-5, Tire repair kit

Front disc brake pads

- For better judgement of remaining pad thickness remove
the front wheel on the drivers side.

- Pull off wheel bolt covers if necessary

01-5, Wheel

securing bolts, tighten to correct torque setting

- Mark position of wheel in relation to brake disc.

- Unbolt wheel securing bolts and remove wheel.

Page 15 / 37

Description of work (part 1 of 2)

Содержание golf 2006






























































































Результаты поиска

Содержание golf 2006

Отзывы:

Похожие инструкции для golf 2006

Бренды по названию

Популярные бренды

Volkswagen golf 2006, Описание работы

Результаты поиска

Содержание golf 2006

Отзывы:

Похожие инструкции для golf 2006

Бренды по названию

Популярные бренды