Volkswagen golf 2006 Скачать руководство пользователя страница 73

Страница: 73 / 93

low temperatures.

Fill with windshield cleanser concentrate G 052 164
in the warmer season also. The powerful cleanser
removes wax and oil deposits from the windows.

Freeze protection (anti-freeze) must be guaranteed
to approx. -25 C (approx. -35 C in countries with an
arctic climate) in the washer system.

Windshield wipe-/wash system, check spray nozzle adjustment,
adjust if necessary

Note:

In the event contamination in spray nozzle produces
an uneven spray pattern, remove spray nozzle

, and rinse it with water in the opposite direction of
spray.

Repair Manual, Electrical Equipment, Repair Group 92,

Subsequently blowing through in the opposite
direction of the spray flow with compressed air is
permitted.

Caution!

Do not use solid objects to clean the spray
nozzles!

Do not use a needle or similar under any
circumstance to adjust spray nozzles, otherwise
the water hoses in the spray nozzles may be
damaged!

Windshield washer system spray jets,

Topic 01-5

Rear window washer nozzle adjustment:

Topic 01-5

Special tools, testers and auxiliary items required

Page 26 / 46

Description of work (part 2 of 2)

Содержание golf 2006






























































































Результаты поиска

Содержание golf 2006

Отзывы:

Похожие инструкции для golf 2006

Бренды по названию

Популярные бренды

Volkswagen golf 2006, Описание работы

Результаты поиска

Содержание golf 2006

Отзывы:

Похожие инструкции для golf 2006

Бренды по названию

Популярные бренды