Volkswagen Marine SDI 50-4 Скачать руководство пользователя страница 37

Страница: 37 / 74

INSPECTION

Renewing oil filter element

Unscrew the cover

Separate the filter element from the cap.

Clean the cover with a clean cleaning

cloth.

Renew the sealing ring on the cover.

Moisten the new sealing ring with oil.

Fit the new filter element in the cover.

Tighten the cover with a tightening

torque of 25 Nm.

Pouring in engine oil

For filling quantities, see the chapter
”Technical data”.
Check the oil level with the oil dipstick - also
see page 33.

The oil level must be between the
two markings and may never be
above the max. mark.

Important

Used oil must be stored in a safe
place out of reach of children
until it is properly disposed of.

Oil must never get into water-

ways, the sewer system or the

ground.

Due to the disposal problem, it is

best to have the engine oil and filter

change carried out by a VW Marine

Service Partner.

BM4-019M

Содержание SDI 50-4











































































Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды

Volkswagen Marine SDI 50-4, Руководство по эксплуатации

Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды