Volkswagen Marine SDI 50-4 Скачать руководство пользователя страница 44

Страница: 44 / 74

INSPECTION

Cleaning air filter element

Wash out and oil the filter element as speci-
fied in the service schedule.

A dirty air filter element can be recognised
from the fact that it has lost its red colour or
the dust deposit
has reached 3 mm.

If the engine is operated in very dusty areas,
clean the filter insert more frequently.

Removing air filter insert

Unscrew the two screws

- see illustra-

tion.

Loosen the clip

- see illustration on

page 44.

Detach the air filter from the intake mani-

fold.

Unscrew the screw

- see illustration -

and remove the air filter housing from the air
filter element.

Cleaning air filter element

Blow out the filter insert with a

maxi-

mum of 2.0 bar compressed air

from

the inside outward.

Important

Wear protective goggles when

blowing out the filter element.
Flying dirt particles can get into
the eyes - danger of injury.

Observe the safety precautions

beginning on page

17 before

performing out any work on the
engine

the

engine

compartment.

Clean the filter element as described in

the instructions on the special cleaning and
service kit available from a VW Marine
Service Partner.

Note

Never use petrol, thinner or other
agents for cleaning! There is a
danger of the filter element being
destroyed.

Wipe out the air filter housing thoroughly.

Cleaning air filter element

BM4-016M

BM5-035M

Содержание SDI 50-4











































































Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды

Volkswagen Marine SDI 50-4, Руководство по эксплуатации

Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды