Volkswagen Marine SDI 50-4 Скачать руководство пользователя страница 40

Страница: 40 / 74

INSPECTION

Renewing filter element

Switch off the engine (single filter) or

switch over to the second filter (double
filter).

Unscrew the 4 cover screws and take off

the cover.

Remove the filter cartridge.

Take out the filter insert by the hoop.

Lay in the new filter element.

Lay the filter cartridge on the filter

element.

Check the cover gasket for damage and

correct seating in the cover.

Note

Should the gasket be damaged, it must be
replaced.

Fit the cover with the gasket and tighten

the screws diagonally.

Note

After renewing the filter element, it is not
necessary to bleed the fuel system.

Turn the ignition key to position 2 (ON) -

see page 16 - and leave it in this position for
approx. 1 minute. This causes the electrical
fuel pump to operate and the fuel system is
filled with diesel.

Start the engine and conduct a visual

inspection of the fuel system for leaks.

Diesel fuel must never get into

waterways, the sewer system or

the ground.

Due to the disposal problem, it is

best to have the filter change carried

out by a VW Marine Service Partner.

Содержание SDI 50-4











































































Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды

Volkswagen Marine SDI 50-4, Руководство по эксплуатации

Результаты поиска

Содержание SDI 50-4

Отзывы:

Похожие инструкции для SDI 50-4

Бренды по названию

Популярные бренды