18
6.1 GENERAL
To ensure the continued safe and efficient operation of the
appliance, it is recommended that it is checked and serviced
at regular intervals. To ensure correct and safe operation of
the appliance, it is essential that any worn or failed compo-
nent be replaced only with a
genuine Vokèra spare part
. It
should be remembered that although certain generic
components may look similar, they will be specific to an
individual appliance or product range. Use of non-genuine
Vokèra spare parts could invalidate your warranty and may
pose a potential safety hazard. The frequency of servicing will
depend upon the particular installation conditions, but in
general, once per year should be sufficient. It is the law that
any servicing work is carried out by competent person such
as a Vokèra engineer, an approved service agent, British Gas,
GAS SAFE registered personnel or other suitably qualified
personnel. The following instructions apply to the appliance
and its controls, but it should be remembered that the central
heating and the domestic hot water systems would also require
attention from time to time.
6.2 ROUTINE ANNUAL SERVICING
•
Check the operation of the appliance and ensure it functions
as described in section 7.
•
Compare the performance of the appliance with its design
specification. The cause of any noticeable deterioration
should be identified and rectified without delay.
•
Thoroughly inspect the appliance for signs of damage or
deterioration especially the flue system and the electrical
apparatus.
•
Check and adjust – if necessary – all burner pressure
settings (see 7.4).
•
Check and adjust – if necessary – the system design pressure
(see 5.10).
5.12 FINAL CHECKS
•
ENSURE ALL TEST NIPPLES ON THE APPLIANCE GAS
VALVE ARE TIGHT AND CHECKED FOR TIGHTNESS.
•
ENSURE THE APPLIANCE FLUE SYSTEM IS FITTED
CORRECTLY AND IS PROPERLY SECURED.
•
ENSURE ALL PIPE WORK IS RE-CHECKED FOR
TIGHTNESS.
•
RE-FIT APPLIANCE CASING.
•
COMPLETE BENCHMARK CHECKLIST.
FOR UK ONLY
Complete details of the boiler, controls, installation and
commissioning in the Benchmark checklist at the back of this
book. It is important that the Benchmark checklist is correctly
completed and handed to the user. Failure to install and com-
mission the appliance to the manufacturers instructions may
invalidate the warranty.
5.13 INSTRUCTING THE USER
Hand over all documentation supplied with this appliance –
including these instructions – and explain the importance of
keeping them in a safe place.
Explain to the user how to isolate the appliance from the gas,
water and electricity supplies and the locations of all drain
points. Show the user how to operate the appliance and any
associated controls correctly.
Show the user the location of the filling valve and how to top-
up the system pressure correctly and show the location of all
manual air release points.
Explain to the user how to turn off the appliance for both long
and short periods and advise on the necessary precautions to
prevent frost damage.
Explain to the user that for continued safe and efficient operation,
the appliance must be serviced annually by a competent
person.
IMPORTANT
To validate the appliance warranty, it’s necessary to register
the appliance details with us. The warranty can be registered
in several ways:
•
by completing the warranty registration card and posting to
us using the envelope supplied
•
online at: vokera.co.uk
•
for UK residents by calling: 0870 607 0281
•
for ROI residents by calling: 056 6655057.
SECTION 6 - SERVICING INSTRUCTIONS
•
Carry out an analysis of the flue gases (see 7.5), and visually
check the condition of the entire flue assembly.
•
Compare the results with the appliance design specification.
Any deterioration in performance must be identified and
rectified without delay.
•
Check that the burner and main heat exchanger are clean and
free from any debris or obstruction.
6.3 REPLACEMENT OF COMPONENTS
Although it is anticipated that this appliance will give years of
reliable, trouble free service, the life span of components will
be determined by factors such as operating conditions and
usage. Should the appliance develop a fault, the fault finding
section will assist in determining which component is
malfunctioning.
6.4 COMPONENT REMOVAL PROCEDURE
To remove a component, access to the interior of the appliance
is essential. Isolate the appliance from the electrical supply
and remove the fuse. And when necessary, close all service
valves on the appliance, remove the appliance casing as
described in section 4.7.1 and drain the water content from
the appliance via the drain valve. Ensure some water
absorbent cloths are available to catch any residual water that
may drip from the appliance or removed component. Under-
take a complete commissioning check as detailed in section
5, after replacing any component.
ALWAYS TEST FOR GAS
TIGHTNESS IF ANY GAS CARRYING COMPONENTS HAVE
BEEN
REMOVED OR DISTURBED.
6.4.1 AIR BOX FRONT COVER REMOVAL (fig. 22)
Locate the 4 screws and remove air box front cover.