manualshive.com logo in svg

Vogt AM Series, Руководство по обслуживанию

Поделиться
Скачать
Vogt AM Series Скачать руководство пользователя страница 19

19

Maintenance

 

•

Adequate and periodic maintenance of the equipment is essential to obtain a good level of performance and an extension of 

the service life.

•

For the motor, the required service intervals and the type of maintenance to be performed are described in the MAINTENANCE 

SCHEDULE described in the respective motor manual provided by the manufacturer.

•

It is recommended that the pump be overhauled at the factory EVERY 3000 OPERATING HOURS OR ONE YEAR, whichever 

comes first.

•

If the pump has been used with water containing suspended solids, sludge, etc., it should be cleaned with clean water after 

the work is completed, in order to reduce corrosion, erosion and remove sediments.

•

ALWAYS USE ORIGINAL SPARE PARTS for maintenance or repair. The use of replacement parts that do not have the same 

quality can damage and shorten the useful life of the equipment.

7.2  

Engine Lubrication

Motor lubrication should be carried out according to the indications given by the motor manufacturer. However, consider that 

some motor manufacturers for their standard lines, contemplate that motors of less than 50 HP do not need relubrication since 

these motors have sealed bearings, therefore only motors of more than 50 HP need relubrication.

7.3   

Electric Motor Drive

Each electric motor has a degree of protection that must satisfy each particular situation; in order to carry out a program of 

revision and cleaning of its internal components, it is advisable to carry out voltage and amperage controls on each phase 

separately.

7.4   

Mechanical Seal

The mechanical seals used as standard in the Monobloc series pumps are of the unbalanced internal monospring type. This 

spring produces the minimum contact force between the sealing surfaces of the rotating and stationary units. The stationary 

unit is mounted on the junction body in an elastomer cup. Its design allows the sealing surfaces to remain in contact, even if 

natural wear or axial and radial oscillations occur in the rotation of the unit. These seals consist of the following elements:

Maintenance

7.1 

General Considerations

!

CAUTION

 

Ceramics

Coal

Buna
Buna

AISI 302
AISI 302

A
B
C
D
E
F

Mono-Spring, Unbalanced

Basic

Tabl

e

 Nº 5

Figur

e

 15

Stationary Ring
Contact Face
Elastomeric Semi Bellows
Cup Type Seat
Spring
Chassis

Ceramics

Coal

Vitón
Vitón

AISI 302
AISI 302

Mechanical Seal

PAC-SEAL Type 21 Seal

Alternative

Содержание AM Series





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды