background image

13

3.  Burn with the spin draft control open for several minutes at numerous intervals throughout the day, being 

careful not to over fire the unit. Following this process will help to warm the chimney and reduce the amount 

of creosote forming condensation within the chimney.

4.  Establish a routine for the handling of fuel, firing, and operating the stove. Check daily for creosote build up 

until experience shows how often you need to clean for safe operation. Be aware that the hotter the fire, 

the less creosote is deposited and weekly cleaning may be necessary in mild weather even though monthly 

cleaning may be enough in the colder months

SOOT - FORMATION & NEED FOR REMOVAL

Additionally, coal combustion by-products like sulphur dioxide, sulphur trioxide and others can corrode stainless 

steel and masonry chimneys. It is important to inspect and clean chimney on a regular schedule. 

CHIMNEY INSPECTIONS 

The chimney connector and chimney should be inspected at the beginning of and at least twice a month 

during the heating season to determine if a creosote or soot build-up has occurred. Chimney fires burn very hot. 

If any part of the stove, chimney or chimney connector should glow red, reduce the fire by closing the damper 

and spin draft control and immediately call the fire department. 

A fire in the stove may be smothered by pouring a large quantity of coarse salt, baking soda, or cool ashes on 

top of the fire.

STOVE JOINTS 

Required Tune-up. This stove is manufactured with cast iron components. IT DOES NOT HAVE WELDED SEAMS. 

Periodic “tune up” may be required by refilling and/ or replacing the cement/joint mortar along the seams where 

the cast iron components meet.

WARNING:

 In case of chimney fire (1) close air inlet control and flue pipe damper. (2) Get out of the house (3) 

call the fire department.

CAUTION:

 RISK OF FIRE. When coal is burned, the products of combustion combine with moisture to form a 

soot residue which accumulates in the flue lining. When ignited, this soot makes an extremely hot fire. The 

chimney connector and chimney should be inspected at least once every two months during the heating 

season to determine if a soot build-up has occurred. If soot has accumulated, it should be removed to 

reduce the risk of a chimney fire.

CAUTION: 

A chimney fire may cause ignition of wall studs or rafters which were assumed to be a safe 

distance from the chimney. If a chimney fire has occurred, have your chimney inspected by a qualified 

expert before using again. 

Содержание THE RANCHER SR57E





















Отзывы: