background image

1

ARROW-Tiger

40-52 ARF ECS

SPORT TRAINER MODEL

WITH POLYCOTE ECS ENHANCED GRAPHICS SYSTEM

TM

ASSEMBLY & OPERATIONS MANUAL

Please review this manual thoroughly before assembling or operating this model.

Proceeding with assembly and use of this product indicates

Agreement With & Acceptance of the following Liability Disclaimer.

Model airplanes, model engines, model engine fuel, propellers and related accessories, tools and equipment can be
hazardous if improperly used. Be cautious and follow all safety recommendations when using your VMAR model air-
plane. Keep hands, tools, clothing and all foreign objects well clear of engines when they are operating. Take particular
care to safeguard and protect your eyes and fingers and the eyes and fingers of other persons who may be nearby.
Use only a good quality propeller that has no cracks or flaws. Stay clear of the propeller and stay clear of the plane of
rotation defined by the propeller.
The Manufacturer, Distributor, Retailer and/or other suppliers of this product expressly disclaim any warranties or repre-
sentations, either expressed or implied, including but not limited to implied warranties of fitness for the purposes of
achieving and sustaining remotely controlled flight.
In no event will the Manufacturer, Distributor, Retailer and/or other suppliers of this product have any obligation arising
from contract or tort, or for loss of revenue or profit, or for indirect, special, incidental, consequential or other damages
arising from the use of this product.
In purchasing and/or using this product, the user accepts all responsibility for its use and accepts all liability associated
with such use.

CAUTION

A Remote Control Model Aircraft is not a toy. It is a flying model that functions much like a full size airplane. If

you do not assemble and operate this product properly you can cause injury to yourself and others and dam-

age property. DO NOT FLY this model if you are not qualified.

You are ultimately responsible for the mechanical, aeronautical and electrical integrity of this model and it's

structure, control surfaces, hinges, linkages, covering, engine, radio, wiring, battery and all other components.

Check all components before and after each flight.

Don't fly until it's right!

The Graphics and Detailing are inside the POLYCOTE ECS!

Содержание ARROW-Tiger

















Отзывы: