Vixen SXD2 Скачать руководство пользователя | Manualshive

Страница: 13 / 112

background image

Chapter 1 PREPARATION

CAUTION: Be sure to handle the counterweight carefully as it is a very heavy item.

The counterweight bar is in the declination body. You may balance the SXD2 mount with only the counterweight bar to start.

1

3

4

2

Tips on Assembling the Mount

Generally  equatorial  mounts  are  heavier  on  the  declination  axis  side.    Because  of  this  feature,  placing  the  SXD2  mount  so  that  its
declination axis comes directly over one of the tripod legs can make it most stable when you use the SXD2 mount for a north (or south)
latitude  of  50  degrees  and  lower.    However,  the  balance  of  the  SXD2  mount  may  vary  if  it  is  used  in  latitude  higher  than  50  degrees.
This  may  result  in  shifting  the  center  of  balance  to  the  opposite  side  of  the  declination  axis  depending  on  the  location  of  the  loading
equipment.  Change the position of the tripod legs so that the SXD2 mount becomes more stable in such a case.

Loosen the counterweight bar lock lever to draw out the counterweight bar.

Tighten the counterweight bar lock lever with the counterweight bar extended fully.

Remove the safety screw on the end of the counterweight bar. Loosen the lock screw on the side of a
counterweight and install the counterweight by sliding it onto the counterweight bar.

Attach the counterweight so that the lock screw on the counterweight
is on the far side of the safety screw as shown in the figure.

Tighten the counterweight lock screw and replace the safety screw to screw it down on the end of the
counterweight bar tightly.

Far Side

.Attaching the Counterweight

Ⅲ

Lock Lever

Counterweight

Bar

Lock Lever

Counterweight

Bar

Counterweight

Counterweight

Safety Screw

Safety Screw

Safety Screw

Safety Screw

Lock Screw

Far Side

Lock Screw

Lock Screw

Lock Screw

13

«
...
11
12
13
14
15
...
»

Содержание SXD2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SXD2

Бренд: d&b audiotechnik Страницы: 14

Бренд: Garmin Страницы: 48

Бренд: A-Tach Mounts Страницы: 2

Бренд: Vebos Страницы: 2

Бренд: B-Tech Страницы: 12

Бренд: KRAFTWERK Страницы: 8

Бренд: KSL Страницы: 2

Бренд: Cavus Страницы: 4

simplicity SLF3

Бренд: Milestone AV Technologies Страницы: 22

Бренд: CNC Router Parts Страницы: 9

FS PentaLock Eco

Бренд: Rehadapt Страницы: 16

Бренд: CONEN Страницы: 7

Бренд: MONSTERMOUNT Страницы: 16

Бренд: Tripp Lite Страницы: 52

Бренд: Eco-Systems Страницы: 3

Бренд: Yamaha Страницы: 2

Stand for Silent Bass BST1

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды