Vixen SXD2 Скачать руководство пользователя | Manualshive

Страница: 69 / 112

background image

Chapter 5 APPLICATION

Remove the optical tube and the counterweights from the
mount.

Loosen  the  altitude  clamp  lever  on  one  side  of  the  mount  body
where  no  latitude  scale  is  attached  and  turn  the  altitude
adjustment knob so
that  the  altitude  of
the  mount  comes
to  a  position  of  35
degrees.
Then,  tighten  the
altitude clamp lever.

Loosen a bolt beneath the altitude clamp lever with the 5mm
Allen wrench and remove it.

Loosen the altitude clamp lever while holding the mount head
with the other hand so that the mount body is moved slowly to
high or low position in altitude.

Move  the  mount  to  a  position  of  55  degrees  in  altitude  if  you
use the mount in the range of high latitude.  Or move the mount
to  a  position  of  15
degrees  in  altitude
if you use the mount
in  the  range  of  low
latitude.  Tighten  the
altitude clamp lever.

Put back the bolt in place and tighten it with the Allen wench
securely.

Loosen the altitude clamp lever again and turn the altitude
adjustment knob so that the mount is set at the latitude of your
observing site.

Tighten the altitude clamp lever and the setting is completed.

Change the Altitude Setting on the SXD2 Mount

The SXD2 is set for use in the middle latitude zone (latitude of 35
degrees  plus/minus  15  degrees)  at  Vixen’s  factory.    If  your
observing  site  is  lower  or  higher  than  the  range  of  the  middle
latitude  zone,  you  need  to  change  the  current  altitude  setting  to
match the latitude of your observing site.
The  range  of  altitude  adjustments  is  divided  into  three  positions
(low,  middle,  and  high)  between  0  degree  and  70  degrees  in
latitude.

1

3

4
5

6

7
8

2

H i g h L a t i t u d e :
Middle Latitude :
L o w l a t i t u d e :

40 degrees up to 70 degrees
20 degrees up to 40 degrees
0 d e g r e e up to 30 degrees

CAUTION

Never tilt the mount body quickly as it may result in
damage or lead to injury.
It is not possible to set the latitude over 70 degrees.

Azimuth Clamp Lever

Azimuth Clamp Lever

Azimuth Adjustment Knob

Azimuth Adjustment Knob

5mm Allen wrench

5mm Allen wrench

Azimuth Clamp Lever

Azimuth Clamp Lever

5mm Allen wrench

5mm Allen wrench

69

«
...
67
68
69
70
71
...
»

Содержание SXD2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для SXD2

Бренд: Garden Страницы: 12

Бренд: Studio Titan Страницы: 11

WHITEBOX SOLUTIONS 1 U

Бренд: Lanner Страницы: 2

Бренд: Yakima Страницы: 10

Бренд: Salamander Designs Страницы: 8

Q-SYS Gooseneck Page Station Podium

Бренд: QSC Страницы: 2

Бренд: Clarke Страницы: 4

Бренд: Crimson Страницы: 8

Smart-Mount SP850-UNL

Бренд: peerless-AV Страницы: 28

Бренд: 3M Страницы: 12

Floor Stand I 40

Бренд: Loewe Страницы: 28

Бренд: Viozon Страницы: 2

On-Wall Equipment GearBox UNI-GB

Бренд: Premier Mounts Страницы: 13

Бренд: Kolpin Outdoors Страницы: 7

Бренд: Blaupunkt Страницы: 8

Бренд: Crestron Страницы: 20

Бренд: Roland Страницы: 6

Бренд: Roland Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды