vividtouch VTE-8400 Скачать руководство пользователя

Страница: 36 / 69

•

Advanced Setting:

Click

Advanced Setting

to display the Advanced Setting window. When you are finished, select

Done

to save

your changes or

Cancel

to discard them.

•

Right Click Simulation:

When this option is enabled, pressing on the screen (as opposed to tapping it) performs

a “right-click” mouse button action. The amount of time the finger must remain on the touch screen to perform this
action is configurable; refer to

Right Click Duration

, below.

•

TUIO (Tangible User Interface Object) Support:

Certain applications require access to touch point messages

via the TUIO protocol. Also, certain operating systems require TUIO to provide multi-touch capability (refer to

Software Requirements (Single-Touch Operation)

on page 20). Therefore, it is recommended that you enable

this option.

•

Right Click Duration:

When Right Click Simulation is enabled, this slider controls how long a finger press action

must be in order for it to be interpreted as a “right-click” action.

•

Double Click Speed:

This slider controls the maximum duration between two touches in order for them to be

interpreted as a “double-click” action.

•

Right/Double Click Range:

This slider controls the maximum distance between two touches in order for them to

be interpreted as a “double-click” or “right-click” action.

•

Reset:

To restore all TouchWin configuration settings to their factory defaults and undo the effects of any previous

calibrations, click

Reset

Содержание VTE-8400






































































Результаты поиска

Содержание VTE-8400

Отзывы:

Похожие инструкции для VTE-8400

Бренды по названию

Популярные бренды

vividtouch VTE-8400, Руководство по установке и эксплуатации

Результаты поиска

Содержание VTE-8400

Отзывы:

Похожие инструкции для VTE-8400

Бренды по названию

Популярные бренды