Vivax ACP-09CH25AEF Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 44

Vivax ACP-09CH25AEF Скачать руководство пользователя страница 31

28

8.4 Operation Modes and Functions

8.4.1 Fan mode.

(1) Outdoor fan and compressor stop.

(2) Temperature setting function is disabled, and no setting temperature is displayed.

(3) Indoor fan can be set to high/med/low/auto.

(4) The louver operates same as in cooling mode.

(5) Auto fan:

8.4.2 Cooling Mode

8.4.2.1 Compressor running rules:

Once the compressor starts up, it will follow the below rules:

When indoor room temp.T1 is lower than Tn, the compressor and outdoor fan will shut off. When T1 is

higher than Tm, the compressor and outdoor fan will start up.

Tm=Ts+1, Tn=Ts.

8.4.2.2 Outdoor fan running rules:

The On-off outdoor units have single fan speed. The outdoor fan will run following the compressor

except when AC is in evaporator high temp.protection in heating mode ,condenser high

temp.protection in cooling mode, defrosting mode and the current protection.

8.4.2.3 Indoor fan running rules

In cooling mode, indoor fan runs all the time and the speed can be selected as high, medium, low and

auto.

PDF

文件使用

"pdfFactory Pro"

试用版本创建

www.fineprint.cn

«
...
29
30
31
32
33
...
»

Содержание ACP-09CH25AEF













































Отзывы:

Нет отзывов