Vivax Metrotech vCam-6 Скачать руководство пользователя страница 13

Страница: 13 / 97

Camera LED Dimmer

Turn the knob to turn on the camera LEDs and to control their brightness.

Distance Counter Reset

Press the reset button to reset the distance shown on the screen to “0”.

Sonde

Press the Sonde button to activate it. The button will glow green and the

sonde icon will appear on the status bar. Press again to switch sonde

frequencies, press again to turn off.

Microphone

Press the

Microphone

button to activate the microphone. The button will

glow red and an icon will appear on the status bar. The unit has a

built-in

microphone

to the left of the microphone button or a microphone

with a 5mm jack can be plugged into the

microphone socket

for use

in noisy areas. Press the microphone button again to turn it off.

The vCam-6 Control Module has other features available. The features

located on the front panel are:

vCam-6

–

Other Features - Front Panel

Содержание vCam-6


































































































Результаты поиска

Содержание vCam-6

Отзывы:

Похожие инструкции для vCam-6

Бренды по названию

Популярные бренды

Vivax Metrotech vCam-6, Тренировка

Результаты поиска

Содержание vCam-6

Отзывы:

Похожие инструкции для vCam-6

Бренды по названию

Популярные бренды