Vito Agro VIMB12TA, Инструкция по эксплуатации

Страница: 32 / 50

32
EN
the machine is always in safe operating
condition.
Cleaning:
The machine must be thoroughly
cleaned in its entirety after use.
Clean the engine by hand (avoid
introducing water into the air filter and
exhaust). Avoid wetting the controls
and other equipment / accessories that
are difficult to dry (water encourages
the appearance of corrosion and rust);
Do not use aggressive cleaning
products. These products can damage
plastics and metals, damaging the safe
operation of your machine
In order to avoid fire hazards, areas of
the cooling air vents, cooling fins and
exhaust should be free from grass,
straw, moss, leaves or grease, and
other wastes.
Maintenance work:
Only maintenance work described in
this instruction manual may be carried
out; all other work must be performed
by an official distributor.
If you lack the necessary knowledge
and resources, always contact an
official distributor.
Use only VITO-approved tools,
attachments, or attachments for this
machine or technically identical parts.
Failure to do so may result in personal
injury or damage to the machine. If you
have any questions, you should contact
an official dealer.
For safety reasons, fuel handling
components (hoses, faucet, tank,
tank cap and connections) should be
checked regularly to detect damage
and leakage. If necessary, they should
be replaced by an official distributor.
Keep the warning and indication
stickers always clean and legible.
Keep all nuts and bolts tight so that the
machine is able to operate safely.
If components or safety devices are
removed for maintenance work, they
must be replaced immediately.
2.7 - STORAGE IN CASE
OF LONGER STOPPING
PERIODS
Let the combustion engine cool down
before putting the machine in an
enclosed space. During operation, the
exhaust becomes extremely hot and
remains so for a few minutes after the
engine is turned off. Avoid touching the
exhaust while it is hot.
Never store the machine with gasoline
in the tank inside a building. Gasoline
vapors that form may come in contact
with flames or sparks and ignite.
Store the machine in a dry location
with the fuel tank empty and the fuel
tank in a well-ventilated, well-closed
compartment. Avoid locations with high
humidity to avoid corrosion and rust.
If the tank is to be emptied, for example,
at the stop before the winter period, the
emptying of the fuel tank must only be
carried out outdoors.
Thoroughly clean the machine before
storage, especially in winter. Store the
machine in an operational state.
Make sure that the machine is
protected against misuse (for example
by children).
2.8 - TECHNICAL ASSISTANCE
Your machine should be repaired only
by the service center of the brand, or
by qualified personnel only with original
spare parts.
3. ASSEMBLY
INSTRUCTIONS
For best performance, place the pump
as close to the level of the water to be
sucked as possible on a level, flat, clean
floor (FIG. C).
With the increase in head (the height
a pump can raise a liquid between the
suction and discharge / discharge water
levels) the pump output decreases.
Minimizing head gauging is equally
important in reducing the self-priming
time (the time it takes for the water to
flow through the suction piping);
The efficiency of the pump is also
influenced by the length, diameter
and type of suction and discharge /
discharge hoses. Use hoses the length
of which does not exceed what is
necessary,
Use short, straight connections to avoid
unnecessary loss. The suction piping
must be fixed to avoid vibration.
Make sure that the filter / spout placed
on the inlet of the suction hose is
immersed more than 30 cm to prevent
air from entering. It should be away
from the banks or limits and from the
bottom of the aspiration site (brook,
levada, weir, well, etc.) to avoid the
entry of debris.
3.1 - MOUNTING THE FILTER /
DRAIN IN THE SUCTION HOSE
(FIG.D)
1. Mount the filter / Plug;
2. EInsert the filter into the suction
hose;
3. Insert and tighten the clamp;
Always insert the filter. This
prevents particles from entering,
preventing damage to the motor pump.
3.2 - MOUNTING THE SUCTION
HOSE (FIG.E)
1. Insert the other end of the suction
hose into the intake hose of the suction
hose connector (11) and attach the
supplied clamp. Tighten tightly;
2. Place the rubber gasket between the