5
ENGLISH
–
The “ROASTING” program operates similarly to a
kitchen stove, the user has to watch the readiness
of food during cooking and switch the unit off, when
the food is ready.
–
See recipes of dishes in the recipe book (sup-
plied with the unit). All recipes are given for
reference only as the required amount and pro-
portions of the ingredients may vary depend-
ing on local peculiarities of the food and altitude
above sea level.
«MAINTAIN t° /OFF» button (19)
Steam release temperature maintenance
After a cooking program is finished the unit is switched
to the keep warm mode automatically (except “Yogurt”
program). Use the button (19) to switch the keep warm
mode on/off.
Note
: Do not use the keep warm function to heat up cold
products.
Switching off / canceling wrong program settings
Use the button (19) to reset settings of the cooking pro-
gram or to switch the cooking program off.
«DELAYED START» button (20)
You can select the time (from 1 hour to 24 hours), after
which the food cooking will be finished.
–
Select a cooking program using the buttons (17),
press the “
DELAYED START
” button (20), use the but-
tons (18) “+ / -” to set the time after which the food
must be ready, the countdown of the time remaining
to the start of cooking will be shown on the display
(3) and after that the selected cooking program will
be switched on.
BEFORE THE FIRST USE
After the unit transportation or storage at low tem-
perature it is necessary to keep it for at least two
hours at room temperature before switching on.
–
Unpack the unit, remove any stickers and package
materials that can prevent normal operation of the
multicooker.
–
Place the unit on a flat, heat-resistant surface away
from all kitchen heat sources (gas cooker, electric
cooker or cooking unit).
–
Place the multicooker keeping at least a 20 cm gap
between the multicooker body and the wall and at
least a 30-40 cm gap above the unit.
–
Do not place the multicooker close to the objects
that can be damaged by the released steam of high
temperature.
Attention! Do not use the unit near bath tubs, kitchen
sinks or other containers filled with water.
–
Open the lid (4) by pressing the button (5) and pull-
ing the handle (6).
–
Wash all the removable parts - the bowl (12), steam
cooking basket (13), soup ladle (14), spatula (15) and
measuring cup (16), yogurt cups (22) and small lids
(23) - with a soft sponge with neutral detergent, then
rinse under running water and dry.
–
Clean the unit body with a damp cloth, then wipe it
dry.
USING OF THE MULTICOOKER
–
Place the food in the bowl following the recipe (see
“Recipe book”).
Note
: Make sure that the ingredients and liquids level
does not exceed the maximal mark “1.8L” andthat it is not
lower than the minimal mark “0.6L”. Maximal level mark
for porridges (except rice) is «1.4L»
General example of loading products and water (as
an example rice is considered)
Measure rice with the measuring cup (16) (one measuring
cup is equal to approximately 160 grams of rice), wash it
and place in the casserole.
Add water up to the corresponding level.
For simplicity use the graduated scale in cups (CUP).
The scale has graduation, marking proportions of rice
and water.
Example:
If you put four measuring cups of cereal, pour
water up to the mark of 4 cups (CUP).
For cooking thin milk porridges the recommended pro-
portion of rice and water is 1:3.
–
Put the bowl (12) in the process chamber. Make sure
that the outer surface of the bowl (12) is clean and
dry, and the bowl itself (12) is placed evenly and is
in secure contact with heating element (10) surface.
Notes:
–
do not use the bowl (12) for washing cereals and
do not chop products in it, this can damage the
non-stick coating;
–
make sure that there are no foreign objects, dirt
or moisture in the process chamber and on the
bottom of the bowl (12);
–
wipe the outer surface and the bottom of the bowl
(12) dry before use;
–
there is a temperature sensor (11) in the middle of
the heating element (10); make sure that nothing
prevents free sensor movement.
–
If you steam products, pour water into the bowl (12)
so that boiling water doesn’t reach the bottom of the
basket (13). Put the basket with food (13) into the
bowl (12).
–
Close the lid (4) until click.
–
Insert the power cord jack into the connector (9) and
the power cord plug into the socket. You will hear a
sound signal, the «8888» symbols will light up on the
display (3) and the “Rice” cooking program indicator
will be flashing.
–
Use the buttons (17) to select the desired auto-
cooking program, the cooking program indicator will
light up
Attention!
If you switched an auto-cooking program on by
pressing one of the buttons (17) without making ad-
ditional program settings, in 10 seconds you will hear
a sound signal and the multicooker will be switched
on in the selected food cooking mode.
–
If necessary, enter the required cooking program
duration time, set the time by consequent pressing
of the buttons (18) «-/+», the numerical data will be
shown on the display (3).
VT-4211_IM.indd 5
24.07.2013 10:48:53
