Vitek VT-3415 B, Инструкция по эксплуатации, Страница: 4 / 24

4
ENGLISH
•
Do not repair the unit by yourself. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
•
To avoid damages, transport the unit in origi-
nal package only.
•
To avoid risk of electric shock or fire, do not
immerse the unit, the power cord and the
power plug of the unit into water or any other
liquids. If the unit was dropped into water:
–
do not touch the water;
–
unplug the unit immediately, only after that
you can take the unit out of water;
–
apply to the authorized service center for
testing and repairing the unit.
•
Keep the unit out of reach of children under
8 years of age.
THE UNIT IS INTENDED FOR HOUSEHOLD USAGE
ONLY
Before using the unit
After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
•
Before using the unit, wash the blender
attachment (1), the whisk (11), the chopping
knife (8), the chopper bowl (7) and the mea-
suring cup (6) with warm water and a neutral
detergent.
• Wipe the motor unit (2), whisk gear (10) and
geared lid (9) with a soft slightly damp cloth and
then wipe it dry.
Attention!
•
Do not immerse the motor unit (2), the whisk
gear (10), the geared lid (9), the power cord
and the power plug into water or any other
liquids.
•
Do not put the attachments and bowls in a
dishwashing machine.
Continuous operation time
•
Continuous operation time with the attach-
ments should not exceed 30 seconds; the
weight of the products to be chopped in the
mini-chopper should not exceed 500 g.
•
Make at least a 3-5 minute break between
operation cycles.
Using the blender attachment
WARNING: Before assembling and installing
the attachments make sure that the power
plug is not inserted into the mains socket.
•
Attach the blender attachment (1) to the
motor unit (2), matching the mark
 on the
motor unit (2) with the mark on the blender
attachment (1) and turn it clockwise till bump-
ing. The mark
 should match the mark on
the blender attachment (1) in fixed position.
•
Insert the power plug into the mains socket.
• Immerse the blender attachment (1) into the
bowl with products that you want to chop/mix;
you can use the measuring cup (6) for it.
• To switch the blender on, press and hold the
button (4). Set the required operation speed
from 1 to 15 using the control knob (5). Use
this operation mode for mixing liquid products.
•
If you press and hold the button (3), the unit
will operate at maximum rotation speed. Use
this operation mode for combined processing
of liquid and hard products.
Notes:
–
Products should be put into the bowl before
the unit is switched on. The amount of pro-
cessed food should not exceed 2/3 of the
capacity of the bowl in which the food is pro-
cessed.
- Before you start chopping/mixing, we
recommend to peel fruit, remove inedible parts,
such as stones, and to cut fruit into approximately
2х2 cm cubes.
• After you finish using the unit, unplug it
and remove the blender attachment (1)
by turning it counterclockwise so that the
mark
 on the motor unit (2) is opposite
the mark .
Attention!
• Do not remove the blender attachment (1)
during operation.
• To avoid damaging the blades, do not pro-
cess too hard products such as cereals,
rice, spices, coffee beans, cheese and
frozen food.
•
While using the blender attachment, if
the products are difficult to process, add
some water into the bowl, if possible.
Using the whisk
Use the whisk (11) only to make cream, biscuit
dough or mixing ready desserts.
WARNING: Before assembling make sure
that the power plug is not inserted into the
power socket.
• Insert the whisk (11) into the gear (10).
• Attach the gear (10) to the motor unit (2),
matching the mark

on the motor unit (2) with
the mark on the gear (10) and turn it clock-
wise till bumping. The mark
 should match
the mark on the gear (10) in fixed position.
VT-3415.indd 4 15.02.2016 11:23:51