Vitek VT-1195, Инструкция по эксплуатации

Страница: 4 / 28

4
ENGLISH
•
Do not leave children unattended to avoid them
using the unit as a toy.
•
For children’s safety reasons do not leave poly-
ethylene bags used as packaging unattended.
Attention! Do not allow children to play with poly-
ethylene bags or packaging film. Danger of suf-
focation!
•
Close supervision is necessary when children
or disabled persons are near the operating unit.
•
If the power cord is damaged, it should be
replaced by the manufacturer, a maintenance
service or similar qualified personnel to avoid
danger.
•
Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any malfunc-
tion is detected or after it was dropped, unplug
the unit and contact any authorized service
center from the contact address list given in
the warranty certificate and on the website
www.vitek.ru.
•
Transport the unit in the original packaging only.
•
Keep the unit out of reach of children and peo-
ple with disabilities.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY. ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES IS
PROHIBITED.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
There may be water spots in the thermopot, this is
normal, as the unit has undergone factory quality
control.
•
Unpack the thermopot; remove any advertis-
ing stickers that can prevent the unit operation.
•
Check the unit for damages, do not use it in
case of damages.
•
Make sure that the unit operating voltage corre-
sponds to the voltage of your mains.
•
Place the thermopot on a dry flat surface keep-
ing at least 20 cm gap between the thermopot
body and the wall or furniture and at least 30 cm
gap above the thermopot.
•
Open the lid (8) by pressing the front part of the
button (9) and holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (13) «FULL».
•
Insert the power cord (18) connector into the
socket on the thermopot body, and plug the
power cord (18) into the mains socket.
•
The boiling mode indicator «BOILING» (6) will
light up on the control panel (4).
•
After water starts boiling, the thermopot will be
switched to the keep warm mode, the indica-
tor (6) will go out and the indicator (7) «KEEP
WARM» will light up.
Note: - the thermopot uses a long boiling technol-
ogy which allows to significantly reduce the chlorine
level in water.
•
Drain the water; to do this set the lock (12)
to the position « » and press on the hand
pump (10).
Attention! Be careful when pouring out water to
avoid burns by hot water.
•
Switch the thermopot off, to do this disconnect
the power cord (18) plug from the mains socket
and disconnect the power cord (18) connector
from the socket.
•
Open the thermopot lid (8) and wait until it cools
down completely.
•
To remove the lid (8) slightly open it and pull the
lid (8) towards yourself taking it by both sides.
•
Carefully tilt the thermopot to drain the remain-
ing water.
•
Install the lid (8) back to its place; to do this
match the ledges on the rear part of the lid (8)
with the grooves in the lid installation place.
Slightly lift the lid and press on it from both sides
to fix. Before using the thermopot make sure
that the lid (8) is fixed properly.
USAGE OF THERMOPOT
•
Open the lid (8) by pressing the button (9) and
holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (13) «FULL».
•
Insert the power cord (18) connector into the
socket (16) on the thermopot body, and plug the
power cord (18) into the mains socket.
•
The boiling mode indicator «BOILING» (6) will
light up on the control panel (4).
•
After water starts boiling, the thermopot will be
switched to the keep warm mode, the indica-
tor (6) will go out and the indicator (7) «KEEP
WARM» will light up.
•
In the keep warm mode you can switch
the reboiling on by pressing the button (5)
«REBOIL», the indicator (6) «BOILING» will light
up and the indicator (7) will go out.
WATER DISPENSING
•
The thermopot can dispense water in 3 ways.
Set the lock (12) to the position « ».
Version 1:
– place a suitable bowl, for instance, a cup under
the spout for pouring water (3) and press the
water dispense button (19).