KF-234 PG2
2
D-302758
KEYFOBS (KF-234 PG2)
Wireless PowerG 2-Way Keyfob
1. INTRODUCTION
KF-234 PG2 is a miniature
PowerG 4-button (6-function)
keyfob, designed for use with the
PowerMax10-G2.
Transmission is initiated by
pressing any one of the four
recessed pushbuttons. Upon
pressing a specific button, the KF-
234 PG2 transmits a PowerG
message associated with the
button that was pressed and
identifiable by PowerMax10-G2
control panels.
Figure 1:
External View
A red LED lights during transmission. When an identified
command
is received by the PowerMax10-G2 control
panel, it acknowledges the command. Upon
acknowledgement, the green LED lights and a happy beep
is heard to indicate successful completion of the command
or the red LED lights and a sad beep is heard to indicate
that the control panel cannot perform the command.
In addition, a battery report is transmitted with
the
outgoing
message. PowerMax10-G2 control panels are designed to
identify this report and operate a corresponding output, if
required.
Each keyfob is supplied with a small key ring.
Operating power is obtained from an internal 3V Lithium
battery.
2. SPECIFICATIONS
Frequency Band (MHz):
Europe: 433, 868, USA: 915
Modulation:
GFSK 50kbs, 25 kHz deviation
Antenna:
Built-in helical antenna
Communication Protocol:
PowerG
Battery type:
3V CR-2032 Lithium battery
Caution!
Risk of explosion if battery is replaced by an
incorrect type. Dispose of used battery according to
manufacturer's instructions.
Battery Life Expectancy:
8 years (for typical use)
Note:
If transmission is still possible despite the battery
condition, the unit will send a low battery signal to the
control panel.
Transmitted Messages:
Arm Away, Arm Home, Arm
Latchkey, Disarm, AUX and Panic.
Operating Temperature:
0° to 55°C (32° to 131°F)
Dimensions:
60 x 34.5 x 12.5 mm
(2-3/8 x 1-3/8 x 1/2 in.)
Weight (including battery):
25 g (0.9 oz)
Color:
Black
Compliance with Standards:
Europe:
EN 300220, EN 50131-1 Grade 2, Class II and
(EN 50134-2 Class II if used for social alarm), EN 301489,
EN 50130-4, EN 60950
USA:
CFR47 Part 15
Canada:
RSS 210
3. ENROLLMENT
Refer to the PowerMax10-G2 Installer Guide for the device enrollment procedure.
4. MODIFY DEVICE SETTINGS
This section describes how to configure the parameters for home monitoring of people from the PowerMax10-G2 control
panel.
To Modify the Keyfob Device Settings
Refer to the PowerMax10-G2 Installer Guide and perform the procedure for Adding A Wireless Device (section 4.4.2), or,
Modifying a Device (section 4.4.5). Then continue below to modify the device settings.
1.
When the PowerMax10-G2 display reads [
DEV SETTINGS
], press
OK
I
.
The PowerMax10-G2 display will read [
AUX A
].
OK
I
2.
Press the
OK
I
button.
The PowerMax10-G2 display will read [
instant
].
OK
I
3.
Press the
or
button repeatedly to select between "
instant
",
"
skip exit delay
" and "
PGM
", for example, "
PGM
".
or
4.
Press
OK
I
to confirm the selection.
The PowerMax10-G2 display will revert to [
AUX A
].
OK
I
AUX A
AUX A
PGM
PGM
instant
