SR-730 PG2
22
D-302758
SIRENS (SR-730 PG2)
Fully Wireless PowerG Outdoor Siren
1. INTRODUCTION
The SR-730 PG2 is a fully wireless outdoor siren,
designed for installation in areas in which wiring action is
difficult or impossible.
The siren is compatible with PowerMax10-G2 control
panels.
Features
•
Siren and strobe light activation:
When an identified
event message is received from the compatible
PowerMax10-G2 alarm system, the siren activates its
sounder & strobe light.
Notes:
The sounder is activated for a predefined "Bell Time"
(refer to
PowerMax10-G2
Installer Guide, par. 4.3),
according to local authorities requirements, or until the
system is disarmed, whichever occurs first.
The strobe light operates as described in the
PowerMax10-G2 Installer Guide, par. 4.3.
•
Tamper indication:
In case of tamper while the system
is armed, the siren transmits the message to the alarm
system and then the alarm system determines whether
the siren should be activated or not. If the siren does not
receive an acknowledge message from the alarm
system, the siren will function independently.
•
Low battery voltage alert
When the battery voltage is low, a low battery message
is sent to the alarm system. After the low voltage
message delivery, at least 2 siren alarms are possible
before the siren is totally inactive.
•
Power Supply Options:
Non-rechargeable battery.
Optional - two non-rechargeable batteries.
•
Sound Types
: Burglar (between 1400Hz - 3200Hz), fire,
gas/Co and flood.
•
Entry/Exit
: Exit delay beeps sound once the user has
armed the system. Entry delay beeps sound once the
user has entered the protected area. (Entry/exit beeps
can be enabled / disabled from the PowerMax10-G2
Installer menu.)
•
Squawk indications:
Squawk (beep) sounds can be
used to indicate alarm system arming (1 squawk) and
disarming (2 squawks) by a keyfob (squawk can be
enabled from the PowerMax10-G2 User menu).
•
Strobe Light Color:
The siren can be purchased with
red, blue, amber or transparent lens, according to the
desired strobe light color.
•
Siren activity LED:
A flashing LED (optional, at the
bottom of the siren front panel) indicates siren activity
(can be disabled by the control panel)
•
Double Tamper protection:
When the siren front panel
is removed or when the siren is removed from the wall,
tamper alarm is sent to the alarm system.
Fig. 1a - External View
Fig. 1b – Mounting
Position
IMPORTANT!
The SR-730 PG2 siren must be installed on
the wall in a vertical position with the screw pointing to the
floor only, as illustrated in Figure 1b.
The importance of
correct positioning of the SR-730 PG2 is to enable the siren
to function as a waterproof device.
•
2-way full supervision
The siren is fully supervised, 2-way communication
device. It includes a receiver, to receive event messages
from the alarm system, and a transmitter, to periodically
transmit its status signal to the alarm system.
Self-test feature
Upon pressing the self test switch, siren functional check
is performed - low level sounds and flash light indicate
that the siren is serviceable.
MCS-730
PC II
Smoke detector
Wireless transmitter
Door or window
open/close detector
Motion detector
PowerMax Pro
PC II
Figure 2- Typical Integration with the Alarm System
2. SPECIFICATIONS
Frequency Band (MHz):
433, 868, USA: 915.
Modulation:
GFSK 50kbs, 25 kHz deviation
Antenna:
Built-in antenna
Communication Protocol:
PowerG II
Siren Type:
One Piezo 109 db min. Sound Pressure Level
@ 1m, 1.4-3.2 kHz, sweep frequency 7 Hz. Additional
piezo is optional.
Battery:
3.6V/14.5A/H Lithium battery (EVE
ER34615M/w200), Visonic assembly cat. No. 0-9912-K.
Note:
The strobe flashes 5 times and the red LED lights
continuously during first battery installation.
Note:
Use only the above battery. Dispose of used battery
according to the manufacturer's instructions.
Battery Life Expectancy:
8 years (for typical use).
Compliance with Standards:
Europe:
EN50131-1 Grade 2 Class 4, EN 50131-4, EN
301489, EN 50130-4, EN 50130-5, EN 300 220, EN 60950-1,
EN 60950-22
Environmental IP55.
USA:
CFR47 Part 15
Canada:
RSS 210
Supervision Time:
4 minutes
Strobe Light:
Pulsed @ 1 sec.
