background image

                                                                                                              BW-108 

                                                                                                                                           

15B 

 
5.4 DMX512 Connection   

 

 

1.  If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin 

adapter-cable. 

2.  At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 

ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug 

and plug it in the DMX-output of the last unit. 

3.  Connect the unit together in a `daisy chain` by XLR plug from the output of the 

unit to the input of the next unit. The cable can not branched or split to a `Y` 

cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables, 

soldered joints or corroded connectors can easily distort the signal and shut 

down the system. 

4.  The DMX output and input connectors are pass-through to maintain the DMX 

circuit, when one of the units’ power is disconnected. 

5.  Each lighting unit needs to have an address set to receive the data sent by the 

controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). 

6.  The end of the DMX 512 system should be terminated to reduce signal errors. 

7.  3 pin XLR connectors are more popular than 5 pin XLR. 

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)   

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),   

Pin 4/5: Not used 

 

                                                                                                              BW-108 

                                                                                                                                           

4B 

 

  2. Technical Specification   
 

y

 DMX 12/9/4 channels selectable 

y

 LED display with password protection at the rear panel 

y

 Come with great built-in programs (16 chases) and 3 editable chases 

y

 Using the latest LED technology makes important energy (cost) savings compared 

to traditional halogen fixtures. 

y

 Completely silent, the projector is cooled by natural air convection without fan 

y

 Thermal sensor in LED PCB to protect LEDs from over heated. 

y

 With waterproof IP66 housing, it perfect to illuminate all kinds buildings like: hotels, 

shops, discotheques, stage, amusement parks, fairground, museum, etc. 

y

 Voltage:100-240V~50/60Hz 

y

 Power consumption: 150W 

y

 Light source: 108×1W LED 

                        50,000hrs rated 

y

 Beam Angle: as indicated on the product label (15°/25°/45° are available) 

y

 Dimension: 582×185×251 mm 

y

 Weight: 18.4 kgs 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание BW-108











Отзывы: